Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 69 / 124

6. Noting the position of the slot on the end, remove the

shift cam assembly. Account for inner and outer
washers.

KC325

7. Remove the counterbalance gear. Account for the

key.

8. Remove the counterbalance shaft.

MD1024

9. Using Crankcase Separator/Crankshaft Remover,

remove the crankshaft.

MD1330

10. Remove the secondary drive gear/secondary driven

gear retaining nut. From inside the crankcase using a
rubber mallet, drive out the output shaft assembly.

Account for the output shaft, a shim, a washer, and

the nut.

Servicing Center

Crankcase Components

SECONDARY GEARS



NOTE: When checking and correcting secondary

gear backlash and tooth contact, the output drive
flange must be secured to the front shaft or false
measurements will occur.

Checking Backlash



NOTE: The rear shaft and bevel gear must be

removed for this procedure. Also, always start with
the original shims on the rear shaft.

1. Place the left-side crankcase cover onto the left-side

crankcase half to prevent runout of the secondary
transmission output shaft.

2. Install the secondary driven output shaft assembly

onto the crankcase.

3. Mount the indicator tip of the dial indicator on the

secondary driven bevel gear (centered on the gear
tooth).

4. While rocking the driven bevel gear back and forth,

note the maximum backlash reading on the gauge.

5. Acceptable

backlash

range

0.05-0.33

(0.002-0.013 in.).

Correcting Backlash



NOTE: If backlash measurement is within the

acceptable range, no correction is necessary.

1. If backlash measurement is less than specified,

remove an existing shim, measure it, and install a
new thinner shim.

2. If backlash measurement is more than specified,

remove an existing shim, measure it, and install a
thicker shim.



NOTE: Continue to remove, measure, and install

until backlash measurement is within tolerance. Note
the following chart.

CAUTION

Do not remove the remaining output shaft assembly
unless absolutely necessary. If the shaft is removed, the
shaft nut must be replaced with a new one and the shaft
must be re-shimmed.



AT THIS POINT

To service crankshaft assembly, see Servicing Center

Crankcase Components sub-section.

Backlash Measurement

Shim Correction

Under 0.05 mm (0.002 in.)

Decrease Shim Thickness

At 0.05-0.33 mm (0.002-0.013 in.)

No Correction Required

Over 0.33 mm (0.013 in.)

Increase Shim Thickness

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды