Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 14 / 124

Adjust the gap to specification (see General Information -

General Specifications). Use a feeler gauge to check the
gap.

ATV0052

When installing the spark plug, be sure to tighten it

securely. A new spark plug should be tightened 1/2 turn
once the washer contacts the cylinder head. A used spark
plug should be tightened 1/8 - 1/4 turn once the washer
contacts the cylinder head.

Muffler/Spark Arrester

At the intervals shown in the Periodic Maintenance

Chart, clean the spark arrester using the following proce-
dure.

1. Remove the cap screws securing the spark arrester

assembly to the muffler; then loosen and remove the
arrester.

KC334A

2. Using a suitable brush, clean the carbon deposits

from the screen taking care not to damage the screen.



NOTE: If the screen or gasket is damaged in any

way, it must be replaced.

3. Install the spark arrester assembly with gasket; then

secure with the cap screws. Tighten to 48 in.-lb.

KC145

Adjusting Throttle Cable

To adjust the throttle cable free-play, follow this proce-
dure.

1. Slide the rubber boot away; then loosen the jam nut

from the throttle cable adjuster.

AL611D

2. Turn the adjuster until the throttle cable has proper

free-play of 3-6 mm (1/8-1/4 in.) at the lever.

ATV-0047

3. Tighten the jam nut against the throttle cable adjuster

securely; then slide the rubber boot over the adjuster.

! WARNING

Wait until the muffler cools to avoid burns.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды