Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 123 / 124

120

AF612D

CHECKING/INFLATING

1. Using an air pressure gauge, measure the air pressure

in each tire. Adjust the air pressure as necessary to
meet the recommended inflation pressure.

2. Inspect the tires for damage, wear, or punctures.



NOTE: If repair is needed, follow the instructions

found on the tire repair kit or remove the wheel and
have it repaired professionally.



NOTE: Be sure all tires are the specified size and

have identical tread pattern.

3. Check the front wheel toe-in and toe-out and adjust

as necessary (see Steering/Frame/Controls - Measur-
ing/Adjusting Toe-Out).

4. Test drive the ATV on a dry, level surface and note

any pulling to the left or right during acceleration,
deceleration, and braking.



NOTE: If pulling is noted, measure the circumfer-

ence of the front and rear tires on the pulling side.
Compare the measurements with the tires on the
opposite side. If pulling is noted during braking only,
check and adjust the brakes as necessary and
recheck

operation

(see

Periodic

Maintenance

Hydraulic Brake Systems).

5. Increase the air pressure in the tires with the smallest

circumference measurement until all tires are equal
in circumference.

6. Repeat steps 4-5 as necessary to ensure proper han-

dling.

Troubleshooting

! WARNING

Do not operate the ATV if tire damage exists.

Problem: Suspension too soft

Condition

Remedy

Spring(s)

weak

Shock absorber

damaged

Shock absorber preload

too low

1. Replace spring(s)
2. Replace shock absorber
3. Adjust shock absorber preload

Problem: Suspension too stiff

Condition

Remedy

A-arm-related bushings

worn

Shock absorber preload

too high

1. Replace bushing
2. Adjust shock absorber preload

Problem: Suspension noisy

Condition

Remedy

Cap screws (suspension system)

loose

A-arm-related bushings

worn

1. Tighten cap screws
2. Replace bushings

Problem: Rear wheel oscillation

Condition

Remedy

Rear wheel hub bearings

worn - loose

Tires

defective - incorrect

Wheel rim

distorted

Wheel hub cap screws

loose

Auxiliary brake

adjusted incorrectly

Rear suspension arm-related bushing

worn

Rear shock absorber

damaged

Rear suspension arm nut

loose

1. Replace bearings
2. Replace tires
3. Replace rim
4. Tighten cap screws
5. Adjust brake
6. Replace bushing
7. Replace shock absorber
8. Tighten nut

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды