Arctic Cat 2014 400 Скачать руководство пользователя | Manualshive

Страница: 44 / 124

background image

41



NOTE: Support the connecting rod with rubber

bands to avoid damaging the rod or install a connect-
ing rod holder.

Servicing Top-Side

Components

VALVE ASSEMBLY

When servicing valve assembly, inspect valve seats,

valve stems, valve faces, and valve stem ends for pits,
burn marks, or other signs of abnormal wear.



NOTE: Whenever a valve is out of tolerance, it must

be replaced.

Cleaning/Inspecting Cylinder Head
Cover



NOTE: If the cylinder head cover cannot be trued,

the cylinder head assembly must be replaced.

1. Wash the cylinder head cover in parts-cleaning sol-

vent.

2. Place the cylinder head cover on the Surface Plate

covered with #400 grit wet-or-dry sandpaper. Using
light pressure, move the cylinder head cover in a fig-
ure eight motion. Inspect the sealing surface for any
indication of high spots. A high spot can be noted by
a bright metallic finish. Correct any high spots
before assembly by continuing to move the valve
cover in a figure eight motion until a uniform bright
metallic finish is attained.

CC130D

Removing Valves



NOTE: Keep all valves and valve components as a

set. Note the original location of each valve set for
use during installation. Return each valve set to its
original location during installation.

1. Using a valve spring compressor, compress the valve

springs and remove the valve keepers. Account for
an upper spring retainer.

CC994

2. Remove the valve seal and the lower remaining

spring seat. Discard the valve seal.

CC134D

CAUTION

Do not allow the connecting rod to go down inside the
crankcase. If the rod is down inside the crankcase and
the crankshaft is rotated, severe damage will result.



AT THIS POINT

To service piston, see Servicing Top-Side Components

sub-section.



AT THIS POINT

To service center crankcase components only, proceed

to Removing Left-Side Components.

CAUTION

Do not remove an excessive amount of the sealing sur-
face or damage to the camshaft will result. Always
check camshaft clearance when resurfacing the cylin-
der head cover.

CAUTION

Water or parts-cleaning solvent must be used in con-

junction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

«
...
42
43
44
45
46
...
»

Содержание 2014 400





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 400

Бренд: Landa Страницы: 101

Бренд: Taylor-Dunn Страницы: 192

Бренд: Honda Страницы: 250

Бренд: Coleman Страницы: 12

Utility Trailer

Бренд: OHIOSTEEL Страницы: 52

Бренд: IBOTECH Страницы: 60

Бренд: Baja motorsports Страницы: 78

Бренд: Landoll Страницы: 62

2013 RANGER RZR 570

Бренд: Polaris Страницы: 152

Бренд: HAPERT Страницы: 45

Бренд: Yamaha Страницы: 138

Бренд: Yamaha Страницы: 154

Sportsman BIG BOSS 6x6

Бренд: Polaris Страницы: 141

Бренд: Taylor-Dunn Страницы: 130

Бренд: Suzuki Страницы: 26

Бренд: TrailMax Страницы: 54

Бренд: TrailMax Страницы: 78

Бренд: Carry-On Trailer Corporation Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды