Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 104 / 124

101

KC425A



NOTE: In some instances it may be necessary to

use an appropriate axle puller to remove the axle
from the differential.

KC486

11. Remove the cap screws from the drive coupler

flange; then remove the upper and lower mounting
cap screws and remove the differential from the
frame.

KC488A

Disassembling Input Shaft



NOTE: This procedure can be performed on a rear

gear case; however, some components may vary
from model to model. The technician should use dis-
cretion and sound judgment.

1. Remove the cap screws securing the front drive actu-

ator and remove the actuator.

CD102

2. Remove the cap screws securing the pinion housing;

then using a rubber mallet, remove the housing.

Account for a gasket. Note the location of all the

components for assembling purposes.

3. Using a side-cutter, remove the boot clamps; then

remove the boots and splined drive from the input
shaft.

4. Remove the input shaft from the pinion housing.

CD107

5. Using the Multi-Seal Remover, remove the input

shaft seal. Account for a spacer.

AF982

6. Remove the snap ring securing the input shaft bear-

ing; then place the pinion housing in a press and
remove the bearing.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды