Arctic Cat 2014 400 Скачать руководство пользователя | Manualshive

Страница: 48 / 124

background image

45

Installing Piston Rings

1. Install ring expander (4) in the bottom groove of the

piston; then install the thin oil rings (3) over the
expander making sure the expander ends do not
overlap. Stagger the end gaps of the upper and lower
thin oil rings according to the illustration.



NOTE: Note the direction of the exhaust side of the

piston (5) for correct ring end gap orientation.

ATV-1085B

2. Install the compression rings (1 and 2) so the letter(s)

on the top surface of each ring faces the dome of the
piston. Rotate the rings until the ring end gaps are on
directly opposite sides of the piston according to the
illustration.



NOTE: The chrome (silver) ring should be installed

in the top position.

MD1343A

CYLINDER/CYLINDER HEAD
ASSEMBLY



NOTE: If the cylinder/cylinder head assembly can-

not be trued, they must be replaced.

Cleaning/Inspecting Cylinder Head

1. Using a non-metallic carbon removal tool, remove

any carbon buildup from the combustion chamber
being careful not to nick, scrape, or damage the com-
bustion chamber or the sealing surface.

2. Inspect the spark plug hole for any damaged threads.

Repair damaged threads using a “heli-coil” insert.

3. Place the cylinder head on the surface plate covered

with #400 grit wet-or-dry sandpaper. Using light
pressure, move the cylinder head in a figure eight
motion. Inspect the sealing surface for any indication
of high spots. A high spot can be noted by a bright
metallic finish. Correct any high spots before assem-
bly by continuing to move the cylinder head in a fig-
ure eight motion until a uniform bright metallic
finish is attained.

Measuring Cylinder Head Distortion

1. Remove any carbon buildup in the combustion

chamber.

2. Lay a straightedge across the cylinder head; then

using a feeler gauge, check the distortion between
the head and the straightedge.

3. Maximum distortion must not exceed specifications.

CC141D

Cleaning/Inspecting Cylinder

1. Wash the cylinder in parts-cleaning solvent.

2. Inspect the cylinder for pitting, scoring, scuffing,

warpage, and corrosion. If marks are found, repair
the surface using a cylinder hone (see Honing Cylin-
der in this sub-section).

CAUTION

Incorrect installation of the piston rings will result in
engine damage.

CAUTION

The cylinder head studs must be removed for this pro-

cedure.

CAUTION

Water or parts-cleaning solvent must be used in con-

junction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

«
...
46
47
48
49
50
...
»

Содержание 2014 400





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 400

Бренд: LaTrax Страницы: 36

Бренд: KAYO MOTO Страницы: 11

1970 SKI-DADDLER

Бренд: AMF Страницы: 74

FourTrax Foreman TRX500FE2 2018

Бренд: Honda Страницы: 279

Бренд: Honda Страницы: 229

Бренд: Honda Страницы: 159

Бренд: Honda Страницы: 71

Centennial A-130-12R

Бренд: Etnyre Страницы: 20

Бренд: Abbey Machinery Страницы: 72

Camoplast ATV T4S

Бренд: CAMSO Страницы: 10

Бренд: HTI Страницы: 6

Бренд: KTM Страницы: 205

Бренд: Hammerhead Страницы: 24

Бренд: Yamaha Страницы: 60

INTIMIDATOR XD 4

Бренд: DFK Страницы: 84

Stand-Up TRIKE/SPYDER/SIDECAR Ride-Up SRL

Бренд: Kendon Страницы: 20

Бренд: ODES Страницы: 92

Бренд: Toro Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды