manualshive.com logo in svg

Arctic Cat 2014 400, Руководство по обслуживанию

Arctic Cat 2014 400 - сервисный мануал для вашего снегохода. Можете скачать бесплатно наш мануал на manualshive.com и получить всю необходимую информацию для обслуживания вашего снегохода. Надежный и качественный продукт для заботы о вашем транспортном средстве в условиях арктического климата.

Поделиться
Скачать
background image

1

TABLE OF CONENTS

General Information........................................................... 2

General Specifications............................................................ 2
Torque Specifications ............................................................. 3
Torque Conversions (ft-lb/N-m)............................................... 4
Break-In Procedure ................................................................ 4
Gasoline - Oil - Lubricant........................................................ 4
Genuine Parts......................................................................... 5
Preparation For Storage ......................................................... 5
Preparation After Storage ....................................................... 6

Periodic Maintenance ........................................................ 7

Periodic Maintenance Chart ................................................... 7
Lubrication Points ................................................................... 8
Air Filter .................................................................................. 8
Valve/Tappet Clearance .......................................................... 9
Testing Engine Compression ................................................ 10
Spark Plug ............................................................................ 10
Muffler/Spark Arrester .......................................................... 11
Adjusting Throttle Cable ....................................................... 11
Adjusting Engine RPM (Idle) ................................................ 12
Engine/Transmission Oil - Filter ........................................... 12
Front Differential/Rear Drive Lubricant ................................. 13
Tires...................................................................................... 13
Driveshaft/Coupling .............................................................. 14
Nuts/Bolts/Cap Screws ......................................................... 14
Ignition Timing ...................................................................... 14
Lights .................................................................................... 14
Shift Lever............................................................................. 16
Frame/Welds/Racks.............................................................. 16
Hydraulic Brake Systems...................................................... 16
Burnishing Brake Pads ......................................................... 18
Checking/Replacing V-Belt .................................................. 18

Steering/Frame/Controls ................................................. 21

Front Body Panel/Fender ...................................................... 21
Rear Body Panel/Rack ......................................................... 22
Steering Post/Tie Rods......................................................... 24
LCD Gauge........................................................................... 25
Handlebar Grip ..................................................................... 26
Throttle Control..................................................................... 26
Steering Knuckles................................................................. 27
Measuring/Adjusting Toe-Out ............................................... 29
Front Rack ............................................................................ 29
Front Bumper Assembly ....................................................... 30
Exhaust System.................................................................... 30
Seat ...................................................................................... 30
Troubleshooting .................................................................... 30

Engine/Transmission....................................................... 32

Troubleshooting .................................................................... 33
Removing Engine/Transmission ........................................... 36
Top-Side Components .......................................................... 38
Removing Top-Side Components ......................................... 38
Servicing Top-Side Components .......................................... 41
Installing Top-Side Components ........................................... 48
Left-Side Components.......................................................... 52
Removing Left-Side Components......................................... 52
Servicing Left-Side Components .......................................... 54
Installing Left-Side Components........................................... 56
Right-Side Components ....................................................... 57
Removing Right-Side Components ...................................... 57

Servicing Right-Side Components ........................................60
Installing Right-Side Components.........................................61
Center Crankcase Components............................................64
Separating Crankcase Halves...............................................64
Disassembling Crankcase Half .............................................65
Servicing Center Crankcase Components ............................66
Assembling Crankcase Half ..................................................71
Joining Crankcase Halves.....................................................73
Installing Engine/Transmission ..............................................74

Fuel/Lubrication/Cooling ................................................ 77

Electric Choke .......................................................................77
Carburetor .............................................................................78
Throttle Cable Free-Play .......................................................83
Engine RPM (Idle).................................................................83
Gas Tank ...............................................................................84
Oil Filter/Oil Pump .................................................................86
Testing Oil Pump Pressure....................................................86
Oil Cooler ..............................................................................87
Troubleshooting .....................................................................87

Electrical System ............................................................. 88

Electrical Connections...........................................................88
Battery...................................................................................88
RPM Limiter ..........................................................................89
Testing Electrical Components..............................................89
Accessory Receptacle/Connector .........................................89
Brakelight Switch (Pressure) .................................................89
Oil Temperature and Cooling Fan Switches ..........................90
Fan Motor ..............................................................................90
Fuse Block/Power Distribution Module..................................91
Ignition Coil ...........................................................................92
Speed Sensor .......................................................................92
Ignition Switch .......................................................................93
Handlebar Control Switches..................................................94
Gear Position Switch .............................................................94
Stator Coil .............................................................................94
Starter Relay .........................................................................95
Starter Motor .........................................................................95
CDI Unit.................................................................................96
Regulator/Rectifier ................................................................96
Lights.....................................................................................96
Ignition Timing .......................................................................98
Troubleshooting .....................................................................98

Drive System .................................................................. 100

Front Differential ..................................................................100
Drive Axles ..........................................................................109
Rear Gear Case ..................................................................111
Hub......................................................................................111
Hand Brake Lever/Master Cylinder Assembly.....................112
Hydraulic Brake Caliper.......................................................113
Troubleshooting Drive System.............................................116
Troubleshooting Brake System............................................116

Suspension .................................................................... 117

Shock Absorbers .................................................................117
Front A-Arms .......................................................................117
Rear A-Arms .......................................................................118
Wheels and Tires ................................................................119
Troubleshooting ...................................................................120

Содержание 2014 400





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 400

wsm RTV900 Workshop Manual preview
RTV900
Бренд: wsm Страницы: 25
Lean Cars B012 Assembly & User Instructions preview
B012
Бренд: Lean Cars Страницы: 12
GMX MOTORBIKES TRACKER 110cc Assembly Manual preview
TRACKER 110cc
Бренд: GMX MOTORBIKES Страницы: 57
Fisher-Price P8013 Owner'S Manual With Assembly Instructions preview
P8013
Бренд: Fisher-Price Страницы: 28
U-Line H-2722 Quick Start Manual preview
H-2722
Бренд: U-Line Страницы: 9
Yamaha FX Nytro FX10X Service Manual preview
FX Nytro FX10X
Бренд: Yamaha Страницы: 859
Baja BR250 Go-Kart Owner'S Manual preview
BR250 Go-Kart
Бренд: Baja Страницы: 55
Futura Club Sport Manual preview
Club Sport
Бренд: Futura Страницы: 24
Kellfri 23-TV15ATV Operating Instructions Manual preview
23-TV15ATV
Бренд: Kellfri Страницы: 24
Yamaha WOLVERINE YFM350FXP Owner'S Manual preview
WOLVERINE YFM350FXP
Бренд: Yamaha Страницы: 167
Yamaha WOLVERINE YFM35XV Owner'S Manual preview
WOLVERINE YFM35XV
Бренд: Yamaha Страницы: 146
Textron Off Road STAMPEDE 900 Parts Manual preview
STAMPEDE 900
Бренд: Textron Off Road Страницы: 166
TrailMaster Challenger 150UTV-X Setup Instruction preview
Challenger 150UTV-X
Бренд: TrailMaster Страницы: 18
Sodi ekokart lpg User Manual preview
ekokart lpg
Бренд: Sodi Страницы: 7
Sodi mini 900 User Maintenance Manual preview
mini 900
Бренд: Sodi Страницы: 28
Sodi Sigma DD2 User Maintenance Manual preview
Sigma DD2
Бренд: Sodi Страницы: 34
Sodi ST32 BV User Maintenance Manual preview
ST32 BV
Бренд: Sodi Страницы: 37
Sodikart Sodi Racing Furia 950 User Maintenance Manual preview
Sodi Racing Furia 950
Бренд: Sodikart Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды