Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 74 / 124

FI663

FI662



NOTE: The countershaft assembly is now ready to

be installed.

Assembling Crankcase

Half



NOTE: For ease of assembly, install components on

the right-side crankcase half.



NOTE: If the output shaft was removed, make sure

that the proper shim is installed.

1. Install the output shaft into the crankcase making

sure the two gears, shim, washer, and nut are in the
correct order.

MD1199

MD1079

2. Apply red Loctite #271 to the threads of the output

shaft. Install and tighten the nut 59 ft-lb. Using a
punch, peen the nut.

MD1333

3. Apply a liberal amount of oil to the crankshaft bear-

ing. Using a propane torch, heat the bearing until the
oil begins to smoke; then slide the crankshaft assem-
bly into place.

MD1334



NOTE: If heating the bearing is not possible, the

crankshaft can be installed using a crankshaft installer.

4. Rotate the crankshaft so the counterweight is toward

the rear of the engine. Install the crank balancer
shaft.

5. Install the key in the crank balancer shaft; then install

the gear and aligning the timing marks, slide the gear
into place.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды