Arctic Cat 2014 400 Скачать руководство пользователя | Manualshive

Страница: 25 / 124

background image

22

6. Remove the electric panel; then disconnect the LCD

gauge connector, ignition switch, and accessory out-
let.

KC210G

7. Remove the front body panel/fender panel.

CLEANING AND INSPECTING

1. Clean all fender components with warm soap and

water.

2. Inspect fenders for cracks and/or loose rivets.

3. Inspect for any missing decals.

INSTALLING

1. Making sure the shift spring is in place and the shift

lever is properly positioned, place the front body
panel/fender panel onto the ATV. With the front rack
in place, loosely install the front rack hardware.

2. Connect the electrical connectors under the electric

panel; then connect the light connectors and attach
onto the frame.

KC210G

KC224

3. Install the screws securing the front body to the front

body supports; then install the left-side and right-side
footwell fasteners. Do not tighten at this time.

4. Place the gas tank cover into position and secure

with the existing hardware; then install the two cap
screws securing the rear of the panel to the frame.
Tighten all cap screws and fasteners securely.

5. Install the electric panel, side panels, and seat.

Rear Body Panel/Rack

REMOVING

1. Remove the rear rack; then remove two cap screws

securing the rear body panel/fender to the side frame
and the cap screws securing the rear fenders to the
footwells.

KC317A

KC316

2. Disconnect the battery (negative cable first) and

remove from the battery compartment; then discon-
nect the starter relay wires and route the wiring out
of the compartment.

«
...
23
24
25
26
27
...
»

Содержание 2014 400





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 400

Бренд: Taylor-Dunn Страницы: 109

TRX250EX Sportrax250EX

Бренд: Honda Страницы: 203

Бренд: Taylor-Dunn Страницы: 136

Бренд: TSE Страницы: 129

Бренд: Kinroad Страницы: 37

Бренд: Realtree Страницы: 12

GE-YX125 series

Бренд: GMX Страницы: 18

Бренд: Jacobsen Страницы: 60

Бренд: E-Z-GO Страницы: 192

Бренд: Radio Flyer Страницы: 22

250GKA-2Z Series

Бренд: Kandi USA Страницы: 16

Бренд: HAKO Страницы: 190

Бренд: Baja motorsports Страницы: 44

Бренд: Yamaha Страницы: 374

2005 FOURTRAX RANCHER AT TRX400FA

Бренд: Honda Страницы: 286

2005 TRX90 Sportrax

Бренд: Honda Страницы: 207

2001 TRX 250 Fourtrax Recon

Бренд: Honda Страницы: 154

2001 TRX400EX Sportrax 400EX

Бренд: Honda Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды