Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 50 / 124

ATV1013A

2. The lobe heights must be greater than minimum

specifications.

Inspecting Camshaft Bearing
Journal

1. Inspect the bearing journal for scoring, seizure

marks, or pitting.

2. If excessive scoring, seizure marks, or pitting is

found, the cylinder head assembly must be replaced.

Measuring Camshaft to Cylinder
Head Clearance

1. Loosen the jam nuts and adjuster screws.

CC005D

2. Place a strip of plasti-gauge in each of the camshaft

lands in the cylinder head.

3. Place the cylinder head cover on the cylinder head

and secure with the cap screws. Tighten securely.



NOTE: Do not rotate the camshaft when measuring

clearance.

4. Remove the cap screws securing the cylinder head

cover to the cylinder; then remove the cylinder head
cover and camshaft.

MD1261

5. Match the width of the plasti-gauge with the chart

found on the plasti-gauge packaging to determine
camshaft to cylinder head and cylinder head cover
clearance.

CC145D

6. If clearance is excessive, measure the journals of the

camshaft.

CC287D



NOTE: If the journals are worn, replace the cam-

shaft; then measure the clearance again. If it is still
out of tolerance, replace the cylinder head.

Inspecting Camshaft
Spring/Unloader Pin

1. Inspect the spring and unloader pin for damage.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды