Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 5 / 124

General Information



NOTE: Some photographs and illustrations used in

this manual are used for clarity purposes only and
are not designed to depict actual conditions.



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

General Specifications

Specifications subject to change without notice.
* One inch below plug threads.
** At the plug threads.

CHASSIS

Tire Size

Front - 24 x 8-12
Rear - 24 x 10-12

Tire Inflation Pressure

27.6 kPa (4 psi)

MISCELLANY

Spark Plug Type

NGK CPR8E

Spark Plug Gap

0.7-0.8 mm (0.028-0.031 in.)

Gas Tank Capacity (rated)

15.1 L (4.0 U.S. gal.)

Rear Drive Capacity

250 ml (8.5 fl oz)*

Front Differential Capacity

275 ml (9.3 fl oz)**

Engine Oil Capacity

3.3 L (3.5 U.S. qt) - Overhaul
2.8 L (3.0 U.S. qt) - Change

Gasoline (recommended)

87 Octane Regular Unleaded

Engine Oil (recommended)

Arctic Cat ACX All Weather
(Synthetic)

Differential/Rear Drive Lubricant

SAE Approved 80W-90 Hyp-
oid

Drive Belt Width (minimum)

28.5 mm (1.12 in.)

Brake Fluid

DOT 4

Taillight/Brakelight

12V/5W/21W

Headlight

12V/35W (4)

FUEL SYSTEM

Carburetor Type

Keihin CVK34

Main Jet

112

Slow Jet

Pilot Screw Setting (turns)

2 1/2

Jet Needle

NLGB

Idle RPM (engine warm)

1250-1350

Starter Jet

Float Height

17 mm

Throttle Cable Free-Play (at lever)

3-6 mm (1/8-1/4 in.)

ELECTRICAL SYSTEM

Ignition Timing

10° BTDC @ 1500 RPM

Spark Plug Cap

4000-6000 ohms

Ignition Coil Resistance

(primary)

(secondary)

Less than 1 ohm
2900-3400 ohms

Ignition Coil Peak Voltage

(primary/CDI) 250-375 DC volts

Stator Coil Resistance

(trigger)

(charging)

90-110 ohms
Less than 1 ohm

Peak Voltage

(trigger) 7.8-9.3 volts

AC Generator Output

(no load) 60 AC volts @ 3000 RPM

Generator Output (approx)

220W @ 5000 RPM

CRANKSHAFT

Connecting Rod (small end)

(max) 20.021 mm

Connecting Rod (big end side-to-side)
(max)

0.7 mm

Connecting Rod (big end width)

21.95-22.00 mm

Connecting Rod (small end deflection)

(max)

3.0 mm

Crankshaft (web-to-web)

60.9 mm

Crankshaft Runout

(max) 0.03 mm

CYLINDER, PISTON, AND RINGS

Piston Skirt/Cylinder Clearance

0.060-0.073 mm

Piston Diameter 15 mm from Skirt End

80.98-81.00 mm

Piston Ring Free End Gap (max)

(1st)

(2nd)

11.6 mm
10.1 mm

Bore x Stroke

81.0 x 71.2 mm

Cylinder Trueness

(max) 0.01 mm

Piston Ring End Gap - Installed

(min) 0.15 mm

Piston Ring to Groove Clearance (max)
(1st/2nd)

0.06 mm

Piston Ring Groove Width

(1st)

(2nd)

(oil)

1.01-1.03 mm
1.21-1.23 mm
2.01-2.03 mm

Piston Ring Thickness

(1st)

(2nd)

0.97-.99 mm
1.17-1.19 mm

Piston Pin Bore

(max) 20.008 mm

Piston Pin

(min) 19.994 mm

VALVES AND GUIDES

Valve Face Diameter

(intake)

(exhaust)

30.6 mm
27.9 mm

Valve/Tappet Clearance

(intake)

(cold engine)

(exhaust)

0.10 mm
0.23 mm

Valve Guide/Stem

(intake)

Clearance (max)

(exhaust)

0.10 mm
0.30 mm

Valve Guide/Valve Stem Deflection

(Wobble Method) (Max)

0.35 mm

Valve Face Radial Runout

(max) 0.15 mm

Valve Guide Inside Diameter

5.000-5.012 mm

Valve Stem Outside Diameter

(intake)

(exhaust)

4.975-4.990 mm
4.951-4.970

Valve Stem Runout

(max) 0.10 mm

Valve Head Thickness (min)

2.30 mm

Valve Face/Seat Width (min)

(intake/exhaust)

0.99 mm

Valve Seat Angle

(intake/exhaust) 45°

Valve Spring Free Length

(min) 40.4 mm

Valve Spring Tension @ 31.1 mm

21.4 kg (47.18

lb)

CAMSHAFT AND CYLINDER HEAD

Cam Lobe Height (min)

(intake/exhaust) 33.53 mm

Camshaft Journal Oil Clearance

(max) 0.040 mm

Camshaft Journal Holder (right & center)
Inside Diameter

(left)

21.98-22.04 mm
17.48-17.53 mm

Camshaft Journal Outside (right & center)
Diameter

(left)

21.97-21.98 mm
17.47-17.48 mm

Camshaft Runout

(max) 0.03 mm

Rocker Arm Inside Diameter

12.000-12.018

Rocker Arm Shaft Outside Diameter

11.975-11.987

Cylinder Head/Cover Distortion

(max) 0.05 mm

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды