Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 22 / 124

KC142A

3. Remove the nut securing the movable drive face to

the clutch shaft; then remove the movable drive face
assembly being careful not to let the roller fall out.

Account for a bushing.

KC127

KC128

4. Thread a cap screw from the V-belt cover into the

driven pulley fixed face and push the movable face
open allowing the V-belt to drop down between the
pulley faces approximately 3/4 in.

KC137

5. Pinching the V-belt together in front of the driven

pulley, pull it forward and outward off the clutch
shaft; then remove it from the driven pulley.

KC136

6. Inspect the faces of the drive and driven pulleys for

scoring, pitting, cracks, or grooving; then clean any
dirt and debris from the V-belt housing and cover.

INSTALLING

1. Place the V-belt onto the driven pulley making sure

the arrows point in the direction of rotation; then
pinch the belt together in front of the driven pulley
and place it over the clutch shaft.

KC135

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды