Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 93 / 124



NOTE: If the meter shows no battery voltage, trou-

bleshoot the battery, fuse, switch, or the main wiring
harness.



NOTE: If the meter shows battery voltage, the main

wiring

harness

good;

proceed

test

the

switch/component or connector.

RESISTANCE (Switch)

1. Remove the spade connectors from the brake switch.

2. Set the meter selector to the OHMS position.

3. Connect the red tester lead to one switch terminal;

then connect the black tester lead to the other switch
terminal.

KC274

4. When the brake pedal is depressed, the meter must

show less than 1 ohm.



NOTE: If the meter shows more than 1 ohm of resis-

tance, replace the switch.

Oil Temperature and

Cooling Fan Switches

1. Connect the meter leads (selector in the OHMS posi-

tion) to the switch contacts.

2. Suspend the switch and a thermometer in a container

of cooking oil; then heat the oil.



NOTE: Neither the switch nor the thermometer

should be allowed to touch the bottom of the con-
tainer or inaccurate readings will occur. Use wire
holders to suspend switch and thermometer.

733-554C

3. On the oil temperature switch when the oil tempera-

ture reaches 160° C (320° F), the meter should read a
closed circuit.

4. On the oil temperature switch, allow the oil to cool,

and when the temperature is at (or just before) a tem-
perature of 140° C (284° F), the meter should read an
open circuit.

5. On the cooling fan switch when the temperature

reaches 120° C (248° F), the meter should read a
closed circuit.

6. On the cooling fan switch, allow the oil to cool, and

when the temperature is at (or just before) a tempera-
ture of 110° C (230° F), the meter should read an
open circuit.

7. If the readings are not as indicated, the switch must

be replaced.

8. Apply thread tape to the threads of the switch; then

install the switch and tighten securely.

9. Connect the switch leads.

Fan Motor

The connector is the black two-prong one located behind
the fan assembly along the right-side frame tube.

KC270A



NOTE: The ignition switch must be in the ON posi-

tion.

! WARNING

Wear insulated gloves and safety glasses. Heated oil

can cause severe burns.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды