Arctic Cat 2014 400 Скачать руководство пользователя | Manualshive

Страница: 96 / 124

background image

93

2. With appropriate needle adapters on the meter leads,

connect the red tester lead to the voltage lead (V);
then connect the black tester lead to the ground lead
(G).

KC248A

3. Turn the ignition switch to the ON position.

4. The meter must show greater than 5.0 volts.

5. Leave the black tester lead connected; then connect

the red tester lead to the signal lead pin (S).

6. Slowly move the ATV forward or backward; the

meter must show 0 and 6 volts alternately.



NOTE: If the sensor tests are within specifications,

the speedometer must be replaced (see Steer-
ing/Frame/Controls - LCD Gauge).

To replace a speed sensor, use the following procedure.

1. Disconnect the three-wire connector from the speed

sensor; then remove the cap screw securing the sen-
sor to the sensor housing.

2. Remove the sensor from the sensor housing account-

ing for an O-ring.

3. Install the new speed sensor into the housing with

new O-ring lightly coated with multi-purpose grease;
then secure the sensor with the cap screw (threads
coated with blue Loctite #242). Tighten securely.

CD071

Ignition Switch

The ignition switch harness connects to the switch with a
three-pin connector. To access the connector, remove the
access panel in front of the handlebar.

KC339D

VOLTAGE



NOTE: Perform this test on the main harness con-

nector.

1. Set the meter selector to the DC Voltage position.

2. Connect the red meter lead to the red/white wire;

then connect the black meter lead to ground.

3. Meter must show battery voltage.



NOTE: If the meter shows no battery voltage, trou-

bleshoot the battery or the main wiring harness.

RESISTANCE



NOTE: Perform this test on the switch harness

using the following procedure.

KC276A

1. Turn the ignition switch to the ON position.

2. Set the meter selector to the OHMS position.

3. Connect either tester lead to pin B; then connect the

other tester lead to pin A.

4. The meter must show less than 1 ohm.

5. Turn the ignition switch to the LIGHTS position.

The meter must show less than 1 ohm.

«
...
94
95
96
97
98
...
»

Содержание 2014 400





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 400

Бренд: E-Z-GO Страницы: 158

120 Sno Pro 2010

Бренд: Arctic Cat Страницы: 562

WILD HP 300 - SERVICE

Бренд: GAS GAS Страницы: 65

Transporta CCT 5221

Бренд: Ifor Williams Trailers Страницы: 45

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 83

PRO HAULER YXP1000

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 194

Бренд: Yamaha Страницы: 287

MINITRANSPORTER MECH 35

Бренд: Fort Страницы: 64

Sportsman 850 Touring EPS

Бренд: Polaris Страницы: 510

Roketa ATV-08L-90

Бренд: Scooter Dynasty Страницы: 12

Бренд: Kellfri Страницы: 8

Бренд: Humbaur Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды