Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 26 / 124

KC322A

3. Remove the auxiliary brake reservoir from the body

but do not disconnect the hose; then route and secure
the hose and reservoir out of the way making sure
not to spill brake fluid.

KC306

4. Using a small screwdriver, remove the light connec-

tors from the frame; then disconnect both connectors
and remove the rear body panel/fender.

KC281

KC279

CLEANING AND INSPECTING

1. Clean all rear body panel components with warm

soap and water.

2. Inspect side panels and rear body panel for cracks

and loose rivets.

3. Inspect threaded areas of all mounting bosses for

stripping.

4. Inspect for missing decals.

INSTALLING

1. Place the rear body panel/fender in place on the

ATV; then secure with the cap screws on the side

frame and the rear rack assembly. Tighten all fasten-
ers securely.

KC317A

KC320A

2. Connect the light connectors and secure to the frame;

then install the battery, starter relay, and auxiliary
brake. Connect all wiring making sure to connect the
positive cables first.

KC279

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды