Arctic Cat 2014 400 Скачать руководство пользователя | Manualshive

Страница: 71 / 124

background image

68

Measuring Connecting Rod
(Big End Side-to-Side)

1. Push the lower end of the connecting rod to one side

of the crankshaft journal.

2. Using a feeler gauge, measure the gap between the

connecting rod and crankshaft journal.

CC289D

3. Acceptable gap range must be within specifications.

Measuring Connecting Rod
(Big End Width)

1. Using a calipers, measure the width of the

connecting rod at the big-end bearing.

2. Acceptable width range must be within specifica-

tions.

Measuring Crankshaft (Runout)

1. Place the crankshaft on a set of V blocks.

2. Mount a dial indicator and base on the surface plate.

Position the indicator contact at point 1 of the crank-
shaft.

KC512

3. Zero the indicator and rotate the crankshaft slowly.

4. Maximum runout must not exceed specifications.



NOTE: Proceed to check runout on the other end of

the crankshaft by positioning the indicator contact at
point 2 and following steps 3-4.

Measuring Crankshaft
(Web-to-Web)

1. Using a calipers, measure the distance from the out-

side edge of one web to the outside edge of the other
web.

KC513

2. Acceptable width range must be within specifica-

tions.

COUNTERSHAFT

Disassembling

1. Remove the reverse driven gear dog; then remove

the circlip securing the reverse driven gear.

FI663

FI664

CAUTION

Care should be taken to support the connecting rod
when rotating the crankshaft.

CAUTION

When disassembling the countershaft, care must be

taken to note the direction each major component (dog,
gear) faces. If a major component is installed facing the
wrong direction, transmission damage may occur
and/or the transmission will malfunction. In either case,
complete disassembly and assembly will be required.

«
...
69
70
71
72
73
...
»

Содержание 2014 400





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 400

Бренд: Kazuma Страницы: 34

Бренд: BERG Страницы: 12

Бренд: Ezgo Страницы: 64

Бренд: Yamaha Страницы: 200

Бренд: Yamaha Страницы: 218

YXZ 1000R SS 2020

Бренд: Yamaha Страницы: 220

Бренд: Yamaha Страницы: 126

Бренд: Suzuki Страницы: 215

Бренд: Yamaha Страницы: 25

Бренд: Yamaha Страницы: 41

Бренд: Yamaha Страницы: 134

4x4 Timberwolf YFB250FWM

Бренд: Yamaha Страницы: 161

Бренд: Yamaha Страницы: 81

4X4 BIG BEAR YFM40FC

Бренд: Yamaha Страницы: 168

4X4 BIG BEAR PROFESSIONAL

Бренд: Yamaha Страницы: 172

2006 GRIZZLY 125

Бренд: Yamaha Страницы: 153

2012 Griizzly 700 YFM7FGPB

Бренд: Yamaha Страницы: 174

2004 Rhino 660 YXR660FAS

Бренд: Yamaha Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды