Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 30 / 124

AF676D

3. Remove the cap screw, lock washer, and washer

securing the actuator arm to the throttle control lever.

AF677D

4. Remove the actuator arm and account for a bushing.

Note the position of the return spring for installing
purposes.

AF678D

INSTALLING

1. Place the return spring into the throttle control; then

place the bushing and actuator arm into position.
Secure with the cap screw, lock washer, and washer.

AF679D

2. Using a pair of needle-nose pliers, place the spring

into position on the actuator arm.

AF680D

3. Place the two halves of the throttle control onto the

handlebar and secure with the two machine screws.

ADJUSTING

To adjust throttle cable free-play, see Periodic Mainte-
nance - Adjusting Throttle Cable.

Steering Knuckles

REMOVING AND DISASSEMBLING

1. Secure the ATV on a support stand to elevate the

wheel; then remove the wheel.

2. Remove the wheel cap from the hub; then remove

the cotter pin from the nut.

3. Remove the nut securing the hub.

4. Remove the brake caliper.

5. Remove the hub assembly.

6. Remove the cotter pin from the tie rod end and

remove the tie rod end from the knuckle.

7. Remove the two cap screws securing the ball joints

in the knuckle.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды