Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 65 / 124

MD1019

3. Install the cam chain.



NOTE: Keep tension on the cam chain to avoid dam-

aging the crankcase boss.

4. Place the pin into position, install the oil pump drive

gear, and tighten the cap screw (coated with red Loc-
tite #271) to 63 ft-lb.

MD1017

MD1018

5. Install the clutch shoe assembly on the crankshaft;

then install the flange nut (left-hand thread) (coated
with red Loctite #271). Tighten to 147 ft-lb.



NOTE: The flat side of the flange nut should be

directed towards the clutch shoe.

6. Install the one-way clutch making sure that the green

dot or the word OUTSIDE is directed away from the
crankcase.

MD1286

KC325A

KC326B

B. Clutch Cover
C. Fixed Drive Face
D. Movable Drive Face



NOTE: Steps 1-6 in the preceding sub-section must

precede this procedure.

7. Install two alignment pins and place the clutch cover

gasket into position. Install the clutch cover.

CAUTION

Care must be taken when installing the flange nut; it has

“left-hand” threads.



AT THIS POINT

Install gear position switch spacer and switch making
sure to align the drive pin with the slot in the shift shaft.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды