Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 90 / 124

Oil Cooler

0743-004

REMOVING



NOTE: It is not necessary to drain the engine oil for

this procedure.

1. Remove the input and output hoses from the fittings

on the cooler.

2. Remove the cap screws securing the oil cooler to the

frame. Account for grommets.

AL651D

3. Remove the oil cooler from the frame.

INSTALLING

1. Place the cooler into position in the frame.

2. Secure the cooler to the frame with the cap screws

and grommets.

3. Install the hoses onto their respective fittings and

secure with the clamps.

Troubleshooting

KEY

1. Oil Cooler Assy

2. Oil Cooler

3. Fan

4. Nut

5. Machine Screw

6. Grommet

7. Shoulder Screw

8. Bushing

9. Clamp

10. Hose

11. Bolt

12. Fitting

13. O-Ring

14. Fitting

CAUTION

Elevate and secure the hoses to avoid oil spillage.

Problem: Starting impaired

Condition

Remedy

Starter jet

obstructed

Starter jet passage

obstructed

Carburetor

leaking air

Gas

contaminated

1. Clean jet
2. Clean passage
3. Replace gasket
4. Drain gas tank and fill with clean gas

Problem: Idling or low speed impaired

Condition

Remedy

Slow jet

obstructed - loose

Slow jet outlet

obstructed

Low speed fuel screw setting

incorrect

Float height

incorrect

1. Clean - tighten jet
2. Clean outlet
3. Adjust screw
4. Adjust float height

Problem: Medium or high speed impaired

Condition

Remedy

High RPM “cut out”

against RPM limiter

Main jet

obstructed

Needle jet

obstructed

Vacuum piston

not operating properly

Filter

obstructed

Float height

incorrect

1. Shift into higher gear - decrease RPM speed
2. Clean main jet
3. Clean needle jet
4. Check piston operation
5. Clean filter
6. Adjust float height

Problem: Overflow and fuel level fluctuations

Condition

Remedy

Float valve

worn - damaged

Float valve spring

broken

Float

not working properly

Float valve

dirty

Float height

too high - too low

1. Replace valve
2. Replace spring
3. Adjust float height - replace float
4. Clean valve
5. Adjust float height

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды