Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 103 / 124

100

Drive System

GENERAL INFORMATION

All gear cases are tagged beneath a cover bolt. This tag is

marked with a production date code, sequence code, and
a ratio code.

The “1” or “3.1” on the lower-right corner indicates a
3.1:1 gear set ratio (11:34 teeth).

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this section.
Refer to the current Special Tools Catalog for the appro-
priate tool description.



NOTE: Special tools are available from the Arctic

Cat Service Department.

Front Differential

REMOVING DIFFERENTIAL

1. Secure the ATV on a support stand to elevate the

wheels.

2. Remove the drain plug and drain the gear lubricant

into a drain pan; then reinstall the plug and tighten to
45 in.-lb.

ATV0082A

3. Remove the front wheels.

4. Pump up the hand brake; then engage the brake lever

lock.

5. Remove the cotter pin securing the hex nut; then

remove the hex nut.

6. Release the brake lever lock.

7. Remove the upper and lower ball joint cap screws

taking care not to strip the threads.

AF628D

8. Pull the steering knuckle away from the axle taking

care not to damage the seals as the axle clears the
knuckle.

KC314

9. Support the axle to not allow it to drop or hang.

10. Pull out on the axle until completely extended; then

push it back in approximately one half inch and pull
out sharply. Repeat until axle spline dislodges from
the gear case.

Ring Gear Backlash

0.28-0.38 mm (0.011-0.015 in.)

Ring Gear End Play

0.1-0.2 mm (0.004-0.008 in.)

Description

p/n

Backlash Measuring Tool

0544-010

CV Boot Clamp Tool

0444-120

Gear Case Seal Installer Tool

0444-224

Internal Hex Socket

0444-104

Pinion Gear/Shaft Removal Tool

0444-127

Slide Hammer Kit

0444-225

Multi-Seal Remover

0644-180

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

CAUTION

Apply pressure to hold the ball joint firmly in the knuckle
or the threads will be stripped when the retaining cap
screws are removed.

CAUTION

The axle must be supported. If the axle is allowed to

drop or hang, damage to the inner CV joint may occur.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды