Arctic Cat 2014 400 Скачать руководство пользователя | Manualshive

Страница: 49 / 124

background image

46

3. Place the cylinder on the surface plate covered with

#400 grit wet-or-dry sandpaper. Using light pressure,
move the cylinder in a figure eight motion. Inspect
the sealing surface for any indication of high spots.

A high spot can be noted by a bright metallic finish.

Correct any high spots before assembly by continu-
ing to move the cylinder in a figure eight motion
until a uniform bright metallic finish is attained.

CC997

Inspecting Cam Chain Guide

1. Inspect cam chain guide for cuts, tears, breaks, or

chips.

2. If the chain guide is damaged, it must be replaced.

Honing Cylinder

1. Using a slide gauge and a dial indicator or a snap

gauge, measure the cylinder bore diameter in three
locations from top to bottom and again from top to
bottom at 90° from the first measurements for a total
of six measurements. The trueness (out-of-round-
ness) is the difference between the highest and low-
est reading. Maximum trueness (out-of-roundness)
must not exceed specifications.

CC397D

2. Wash the cylinder in parts-cleaning solvent.

3. Inspect the cylinder for pitting, scoring, scuffing, and

corrosion. If marks are found, repair the surface
using a #320 grit ball hone.



NOTE: To produce the proper 60° cross-hatch pat-

tern, use a low RPM drill (600 RPM) at the rate of 30
strokes per minute. If honing oil is not available, use
a lightweight petroleum-based oil. Thoroughly clean
cylinder after honing using soap and hot water. Dry
with compressed air; then immediately apply oil to
the cylinder bore. If the bore is severely damaged or
gouged, replace the cylinder.

CC390D

4. If any measurement exceeds the limit, the cylinder

must be replaced.

Measuring Camshaft Runout



NOTE: If the camshaft is out of tolerance, it must be

replaced.

1. Place the camshaft on a set of V blocks; then position

the dial indicator contact point against the shaft and
zero the indicator.

CC283D

2. Rotate the camshaft and note runout; maximum tol-

erance must not exceed specifications.

Measuring Camshaft Lobe Height

1. Using a calipers, measure each cam lobe height.

CAUTION

Water or parts-cleaning solvent must be used in con-

junction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

«
...
47
48
49
50
51
...
»

Содержание 2014 400





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 400

Бренд: Hisun Страницы: 116

Бренд: Yamaha Страницы: 213

Бренд: Yamaha Страницы: 282

Бренд: Yamaha Страницы: 443

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 130

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 154

Бренд: Yamaha Страницы: 160

Бренд: Yamaha Страницы: 162

Бренд: Yamaha Страницы: 184

Бренд: Yamaha Страницы: 328

Бренд: Yamaha Страницы: 409

Бренд: gio Страницы: 22

545 XC ATV EU 2011

Бренд: KTM Страницы: 221

Turf Cat 628 ROPS

Бренд: Jacobsen Страницы: 9

Бренд: ODES Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды