Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 43 / 124

9. Remove the cylinder head from the cylinder, remove

the gasket, and account for two alignment pins.

MD1163

10. Remove the cam chain guide.

MD1173

C. Cylinder
D. Piston



NOTE: Steps 1-10 in the preceding sub-section

must precede this procedure.

11. Remove the two nuts securing the right side of the

cylinder to the right-side crankcase half.

KC337A

12. Lift the cylinder off the crankcase taking care not to

allow the piston to drop against the crankcase.

Account for the gasket and two alignment pins.

MD1214

13. Using an awl, remove the piston-pin circlips. Take

care not to drop them into the crankcase.

MD1213

14. Using Piston Pin Puller, remove the piston pin.

Account for the opposite-side circlip. Remove the

piston.



NOTE: It is advisable to remove the opposite-side

circlip prior to using the puller.

MD1219



AT THIS POINT

To service valves and cylinder head, see Servicing
Top-Side Components sub-section.



AT THIS POINT

To inspect cam chain guide, see Servicing Top-Side

Components sub-section.



AT THIS POINT

To service cylinder, see Servicing Top-Side Compo-

nents sub-section.

CAUTION

When removing the cylinder, be sure to support the pis-

ton to prevent damage to the crankcase and piston.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды