Arctic Cat 2014 400 Скачать руководство пользователя | Manualshive

Страница: 56 / 124

background image

53

MD1186

3. Using Crankcase Separator/Crankcase Remover and

the 6 mm adapter, remove the left-side cover w/stator
assembly. Account for the two alignment pins and
the position of the shifter bracket for installing pur-
poses.

CC946

MD1188



NOTE: Inspect the inside of the left-side cover for

any shaft washers that may have come off with the
cover. Make sure they are returned to their respective
shafts and that the starter idler gear spacer is on the
shaft or in the cover.

B. Rotor/Flywheel
C. Starter Motor



NOTE: Steps 1-3 in the preceding sub-section must

precede this procedure.

4. Remove the rotor/flywheel nut.

MD1194

5. Install the crankshaft protector.

MD1365

6. Using Magneto Rotor Remover, break the rotor/fly-

wheel assembly loose from the crankshaft. Remove
the remover, the crankshaft protector, the rotor/fly-
wheel, and the starter clutch gear. Account for the
key.

MD1368

CAUTION

Care must be taken that the remover is fully threaded
onto the rotor/flywheel or damage may occur.

«
...
54
55
56
57
58
...
»

Содержание 2014 400





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 400

Polar Trailer 10537

Бренд: Clam Страницы: 7

Бренд: Linhai Страницы: 93

Бренд: XY Powersports Страницы: 259

Бренд: Irbis Страницы: 99

Бренд: Coleman Страницы: 12

Бренд: Suzuki Страницы: 492

Giga-Trailer 1840

Бренд: Strautmann Страницы: 39

Outlander X mr Series

Бренд: Can-Am Страницы: 196

amphibious, off-road utility vehicle

Бренд: Centaur Страницы: 56

Бренд: Duralite Страницы: 27

Бренд: Lynx Страницы: 196

Бренд: Kärcher Страницы: 16

MIC 45 advanced

Бренд: Kärcher Страницы: 19

Бренд: P.Lindberg Страницы: 107

Бренд: Hammerhead Off-Road Страницы: 75

QUAD WILD HP 300 RV - 2005

Бренд: GAS GAS Страницы: 72

Бренд: Yamaha Страницы: 38

Бренд: Yamaha Страницы: 293

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды