Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 121 / 124

118

KC297

8. Remove the lower shock absorber eyelet from the

upper A-arm.

9. Remove the cap screws securing the A-arms to the

frame.

10. Remove the circlip from the ball joint; then remove

the ball joint from the A-arm.

CLEANING AND INSPECTING

1. Clean all A-arm components using a pressure

washer.

2. Clean the ball joint mounting hole of all residual

Loctite, grease, oil, or dirt for installing purposes.

3. Inspect the A-arm for bends, cracks, and worn bush-

ings.

4. Inspect the ball joint mounting holes for cracks or

damage.

5. Inspect the frame mounts for signs of damage, wear,

or weldment damage.

INSTALLING

1. Apply green Loctite #609 to the entire outside diam-

eter of the ball joint; then install the ball joint into the

A-arm and secure with the circlip.

2. Install the A-arm assemblies into the frame mounts

and secure with the cap screws. Only finger-tighten
at this time.

3. Secure the lower eyelet of the shock absorber to the

upper A-arm. Tighten nut to 35 ft-lb.

4. Secure the A-arm assemblies to the frame mounts

(from step 2). Tighten the cap screws to 35 ft-lb.

5. Install the knuckle assembly onto the ball joints and

secure with cap screws. Tighten to 35 ft-lb.

6. Apply grease to the hub and drive axle splines; then

install the hub assembly onto the drive axle.

7. Secure the hub assembly with the nut. Tighten only

until snug.

8. Secure the brake caliper to the knuckle with the two

“patch-lock” cap screws. Tighten to 20 ft-lb.

9. Secure the hub nut (from step 7) to the shaft/axle.

Tighten to 200 ft-lb.

10. Install a new cotter pin and spread the pin to secure

the nut.

11. Install the wheel and tighten to 40 ft-lb (steel) or 80

ft-lb (aluminum).

12. Remove the ATV from the support stand.

Rear A-Arms

REMOVING

1. Secure the ATV on a support stand to elevate the

wheels

2. Pump up the hand brake; then engage the brake lever

lock.

3. Remove the wheel.

4. Remove the cotter pin securing the hex nut; then

remove the hex nut. Release the brake lever lock.

5. Remove the caliper (right side only).



NOTE: Do not allow the brake caliper to hang from

the hose.

6. Remove the cap screws and lock nut securing the

shock absorber to the frame and lower A-arm; then
remove the shock absorber.

KC0100

7. Slide the hub out of the knuckle and set aside.

8. Remove the cap screws and lock nuts securing the

knuckle to the A-arms. Discard the lock nuts.



NOTE: Never reuse a lock nut. Once a lock nut has

been removed, it must be replaced with a new lock
nut.

9. Remove the cap screws and lock nuts securing the

A-arms to the frame; then remove the A-arms.

CAUTION

Do not tighten the nut beyond the 35 ft-lb specification
or the shock eyelet or mount WILL be damaged.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды