Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 83 / 124

CC761A

7. Secure the needle jet holder with a wrench; then

remove the main jet.

8. Remove the needle jet holder; then remove the nee-

dle jet, slow jet, and the starter jet.

9. Remove the pilot screw. Account for a spring,

washer, and an O-ring.

KC0028A

KC0029A

10. Unscrew and remove the idle adjust screw. Account

for the spring and washer.

CLEANING AND INSPECTING.

1. Place all metallic components in a wire basket and

submerge in carburetor cleaner.

2. Soak for 30 minutes; then rinse with clean, hot water.

3. Wash all non-metallic components with soap and

water. Rinse thoroughly.

4. Dry all components with compressed air only mak-

ing sure all holes, orifices, and channels are unob-
structed.

5. Inspect the carburetor body for cracks, nicks,

stripped threads, and any imperfections in the cast-
ing.

6. Inspect the vacuum piston/diaphragm for cracks,

imperfections in the casting, or cracks and tears in
the rubber.

7. Inspect float for damage.

8. Inspect gasket and O-rings for distortion, tears, or

noticeable damage.

9. Inspect tips of the jet needle, pilot screw, and the

needle jet for wear, damage, or distortion.

10. Inspect the slow jet and main jet for obstructions or

damage.



NOTE: If the slow jet is obstructed, the mixture will

be extremely lean at idle and part-throttle operation.

11. Inspect the float valve for wear or damage.

12. Inspect the carburetor mounting flange for damage

and tightness.

ASSEMBLING

1. Thread the idle adjust screw into the carburetor mak-

ing sure the washer and spring are properly posi-
tioned.

2. Install the pilot screw, spring, washer, and O-ring.

KC0029A

! WARNING

When drying components with compressed air, always

wear safety glasses.

CAUTION

NOT

place

any

non-metallic

components

parts-cleaning solvent because damage or deterioration
will result.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды