Arctic Cat 2014 400 Скачать руководство пользователя | Manualshive

Страница: 54 / 124

background image

51

17. Apply red Loctite #271 to the first cap screw secur-

ing the sprocket and tab washer to the camshaft; then
install the cap screw and tab washer. Tighten cap
screw only until snug.

CC404D

MD1137

18. Rotate the crankshaft until the second cap screw

securing the sprocket to the camshaft can be
installed; then install the cap screw (threads coated
with red Loctite #271). Tighten to 11 ft-lb; then bend
the tab to secure the cap screw.

MD1137

19. Rotate the crankshaft until the first cap screw (from

step 17) securing the sprocket to the camshaft can be
addressed; then tighten to 11 ft-lb. Bend the tab to
secure the cap screw.

20. Install the cylinder head plug with the cupped end

facing the camshaft and the opening directed down-
wards.

21. Remove the cap screw from the end of the chain ten-

sioner. Account for the plunger, spring, and gasket.

MD1248

22. Depress the spring-loaded lock and push the plunger

into the tensioner.

MD1146

23. Place the cam chain tensioner assembly and gasket

into the cylinder making sure the ratchet side is fac-
ing toward the top of the cylinder and secure with the
two cap screws.

MD1254

24. Install the cap screw and spring into the end of the

cam chain tensioner. Tighten securely.

CAUTION

Care must be taken that the tab washer is installed cor-
rectly to cover the alignment hole on the sprocket. If the
alignment pin falls out, severe engine damage will
result.

«
...
52
53
54
55
56
...
»

Содержание 2014 400





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 400

Бренд: KAYO MOTOR Страницы: 90

Бренд: Go Kart Страницы: 20

1997 Fourtrax TRX250

Бренд: Honda Страницы: 155

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 76

Black-Topper Shooter II

Бренд: Etnyre Страницы: 51

Black-Topper SHOOTER Series

Бренд: Etnyre Страницы: 84

2007 Outlander 500 EFI

Бренд: Can-Am Страницы: 148

Бренд: FarmTek Страницы: 5

Бренд: Columbia Страницы: 40

Бренд: Leggero Страницы: 98

Minor VM Hydrostatic

Бренд: Scarab Страницы: 32

Бренд: Humbaur Страницы: 230

Бренд: Bad Boy Страницы: 143

Бренд: NC Страницы: 84

Fourtrax TRX 250TM

Бренд: Honda Страницы: 224

Бренд: Taylor-Dunn Страницы: 260

Бренд: Yamaha Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды