Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 80 / 124

Fuel/Lubrication/Cooling



NOTE: Arctic Cat recommends the use of new gas-

kets, lock nuts, and seals and lubricating all internal
components when servicing the engine/transmis-
sion.

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this section.
Refer to the current Special Tools Catalog for the appro-
priate tool description.



NOTE: Special tools are available from the Arctic

Cat Service Department.

Electric Choke

REMOVING

1. Disconnect the electric choke connector from the

wiring harness; then remove the screw securing the
choke body to the carburetor.

2. Carefully remove the choke assembly from the car-

buretor taking care not to force the plunger from the
carburetor body.

INSPECTING/TESTING

1. Inspect the plunger (A) for scoring or scratches, the

needle (B) for damage to the tip, the spring (C) for
breakage, and the O-ring (D) for breaks.

KC328A

2. With the choke at room temperature (approximately

70° F), measure plunger extension. Measurement (A)
should be 18.6-19.1 mm.

KC328B

3. Connect Electric Choke Test Harness to the choke

connector and a suitable 12 DC volt power supply
for 2-3 minutes. Disconnect the power and measure
plunger extension. Measurement (B) should be
22.1-23.4 mm.

KC328C

4. If the choke is damaged or the measurements are not

within specifications, the choke must be replaced.

INSTALLING

1. Lightly lubricate the O-ring on the choke body; then

carefully insert the choke assembly into the carbure-
tor being careful not to damage the plunger.

2. Secure the choke with the screw and tighten

securely; then connect the choke connector to the
wiring harness.

Description

p/n

Electric Choke Test Harness

0444-247

Oil Pressure Test Kit

0644-495

Tachometer

0644-275

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды