Arctic Cat 2014 400 Скачать руководство пользователя страница 68

Страница: 68 / 124

CC869



NOTE: To keep the shaft/gear assemblies intact for

identification, tap the shafts toward the left-side
crankcase half when separating the halves.

MD1313

Disassembling Crankcase

Half

1. Remove the secondary and primary driveshaft

assemblies. Account for the bearing alignment
C-ring on the bearing boss next to the driven gear.

MD1317



NOTE: Note the location of the bearing alignment

pin on the secondary output shaft.

2. Remove the reverse idler gear, spacer, and sleeve.

Account for the washer.

MD1325

3. Remove the driveshaft.

MD1326

4. Remove the shift fork shaft and the outer shift fork.

MD1327

5. Remove snap ring and gear from the output side of

the gear cluster. Remove the gear cluster and the
inner shift fork together. Account for snap ring, gear,
and washer.

MD1328

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды