Arctic Cat 2014 400 Скачать руководство пользователя страница 101

Страница: 101 / 124

3. Set the tester to DC VOLTS; then turn the ignition

switch to the ON position and move the shift lever to
the R (reverse) position. The meter must show bat-
tery voltage.



NOTE: If the meter does not show battery voltage,

use the following procedure to troubleshoot.

4. Remove the black tester lead from the brown/laven-

der wire and connect to a suitable ground.

A. If the meter shows battery voltage, troubleshoot

the gear shift position switch connector or the
gear shift position switch.

B. If the meter does not show battery voltage, inspect

the LIGHTS fuse, ignition switch, or the main
wiring harness.

Ignition Timing

The ignition timing cannot be adjusted; however, verify-
ing ignition timing can aid in troubleshooting other com-
ponents.

verify

engine

timing,

see

Periodic

Maintenance -Ignition Timing.

Troubleshooting

Problem: Spark absent or weak

Condition

Remedy

Ignition coil

defective

Spark plug

defective

Alternator

defective

CDI unit

defective

Pick-up coil

defective

1. Replace ignition coil
2. Replace plug
3. Replace stator coil
4. Replace CDI unit
5. Replace stator coil

Problem: Spark plug fouled with carbon

Condition

Remedy

Gasoline

incorrect

Air cleaner element

dirty

Spark plug

incorrect (too cold)

Valve seals

cracked - missing

Oil rings

worn - broken

Mixture

too rich

Idling RPM

too high

1. Change to correct gasoline
2. Clean element
3. Replace plug
4. Replace seals
5. Replace rings
6. Replace jets with correct size
7. Adjust carburetor

Problem: Spark plug electrodes overheat or burn

Condition

Remedy

Spark plug

incorrect (too hot)

Engine

overheats

Spark plug

loose

Mixture

too lean

1. Replace plug
2. Service oil filter
3. Tighten plug
4. Replace jets with correct size

Problem: Alternator does not charge

Condition

Remedy

Stator wires/connections

shorted - loose - open

Stator coils

shorted - grounded - open

Regulator/rectifier

defective

1. Repair - replace - tighten stator wires
2. Replace stator coils
3. Replace regulator/rectifier

Problem: Alternator charges, but charging rate is below the specification

Condition

Remedy

Stator wires

shorted - open - loose (at terminals)

Stator coils

grounded - open

Regulator/rectifier

defective

Battery

defective

Electrolyte

low

1. Repair - tighten Stator wires
2. Replace stator coils
3. Replace regulator/rectifier
4. Replace battery
5. Add distilled water

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды