Arctic Cat 2014 400 Скачать руководство пользователя

Страница: 9 / 124

Preparation After

Storage

Taking the ATV out of storage and correctly preparing it
will assure many miles and hours of trouble-free riding.

Arctic Cat recommends the following procedure to pre-

pare the ATV.

1. Clean the ATV thoroughly.

2. Clean the engine. Remove the cloth from the muffler.

3. Check all control cables for signs of wear or fraying.

Replace if necessary.

4. Change the engine/transmission oil and filter.

5. Charge the battery; then install. Connect the battery

cables.

6. Check the entire brake systems (fluid level, pads,

etc.), all controls, lights, and headlight aim; adjust or
replace as necessary.

7. Tighten all nuts, bolts, cap screws, and screws mak-

ing sure all calibrated nuts, cap screws, and bolts are
tightened to specifications.

8. Check tire pressure. Inflate to recommended pressure

as necessary.

9. Make sure the steering moves freely and does not

bind.

10. Check the spark plug. Clean or replace as necessary.

CAUTION

The ignition switch must be in the OFF position prior to

installing the battery or damage may occur to the igni-
tion system.

CAUTION

Connect the positive battery cable first; then the nega-
tive.

Содержание 2014 400





























































































































Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды

Arctic Cat 2014 400, Руководство по обслуживанию

Результаты поиска

Содержание 2014 400

Отзывы:

Похожие инструкции для 2014 400

Бренды по названию

Популярные бренды