Can-Am Outlander 400 EFI 2009 Operator'S Manual Download

Page: 1 / 160

Vmo2008-016_OUTLANDER_MAX400EFI_219000498_ANG.FH10 Fri Oct 05 09:11:41 2007 Page 1

Composite

CY CMY

THIS VEHICLE CAN BE HAZARDOUS TO OPERATE.

A collision or rollover can occur quickly, even during

routine maneuvers such as turning and driving on hills

or over obstacles, if you fail to take proper precautions.

SEVERE INJURY OR DEATH

can result if

you do not follow these instructions:

BEFORE YOU OPERATE THIS VEHICLE, READ

THIS

OPERATORS GUIDE

AND ALL ON-PRODUCT

LABELS.

 NEVER OPERATE THIS VEHICLE WITHOUT

PROPER INSTRUCTIONS.

Beginners should

complete a certified training course.

NEVER CARRY MORE THAN ONE PASSENGER.

You increase your risk of losing control if you carry

more than one passenger.

 NEVER OPERATE THIS VEHICLE ON A PAVED

SURFACE.

You increase your risk of losing control

if you operate this vehicle on pavement.

 NEVER OPERATE THIS VEHICLE ON PUBLIC

ROADS.

You can collide with another vehicle if you

operate this vehicle on a public road.

 OPERATOR AND PASSENGER SHOULD ALWAYS

WEAR AN APPROVED HELMET,

eye protection, and

protective clothing.

 NEVER CONSUME ALCOHOL OR DRUGS

before or while riding this vehicle.

 NEVER OPERATE THIS VEHICLE AT EXCESSIVE

SPEEDS.

You increase your risk of losing control

if you operate this vehicle at speeds too fast for the

terrain, visibility conditions, or your experience.

NEVER ATTEMPT WHEELIES, JUMPS, OR OTHER

STUNTS.

WARNING

Read this guide thoroughly. It contains important safety information.

Minimum recommended age: Operator: 16 years. Passenger: 12 years. Do not remove this Operators Guide from the vehicle.

WARNING

® AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES.

219 000 498

OPERATORS GUIDE, OUTLANDER MAX 400 EFI / ENGLISH

GUIDE DU CONDUCTEUR, OUTLANDER MAX 400 EFI / ANGLAIS

FAIT AU / MADE IN CANADA

U/M:P.C.

2 1 9 0 0 0 4 9 8

Includes

Safety, Vehicle

and

Maintenance Information

Operators

Guide

OUTLANDER

MAX

400 EFI

OUTLANDER

MAX

400 EFI

Summary of Contents for Outlander 400 EFI 2009

































































































































































Search results

Summary of Contents for Outlander 400 EFI 2009

Reviews:

Related manuals for Outlander 400 EFI 2009

Brands by name

Popular brands

Can-Am Outlander 400 EFI 2009, Operator'S Manual

Search results

Summary of Contents for Outlander 400 EFI 2009

Reviews:

Related manuals for Outlander 400 EFI 2009

Brands by name

Popular brands