Altera Stratix II GX страница 374 Скачать руководство пользователя

Страница: 374 / 672

3–126

Altera Corporation

Stratix II GX Device Handbook, Volume 2

October 2007

Channel and Clock Multiplier Unit (CMU) PLL Reconfiguration

how many input clocks

3 (77.76 MHz, 125 MHz, and
106.25 MHz). Assume:
clock2 = 77.76 MHz
clock1 = 125 MHz
clock0 = 106.25 MHz

what is the select input clock source for
transmitter and receiver PLL

what is the reconfig protocol driven by
clock1

GIGE

what is clock1 input frequency

125 MHz

use clock 1 reference clock divider

do not check this option

what is the reconfig protocol driven by
clock2

SONET/SDH

what is clock2 input frequency

77.76 MHz

use clock 2 reference clock divider

do not check this option

Reconfig2 Tab Settings

how should the receivers be clocked

select

use respective core clocks

since you clock the receive parallel date
with

tx_clkout

for the GIGE protocol

and

rx_clkout

for the other two

protocols. Refer to the

Stratix II GX

Transceiver Architecture Overview

chapter in volume 2 of the

Stratix II GX

Device Handbook

for more information

about these options.

how should the transmitters be clocked use the respective channel transmitter

core clocks.

check the control box to use the
corresponding control port

select the protocol-specific signals. For
SONET/SDH, you need

rx_byteorderalignstatus

rx_ala2sizeout

, etc. Refer to the

Stratix II GX ALT2GXB Megafunction
User Guide

chapter in volume 2 of the

Stratix II GX Device Handbook

for more

information.

Basic1 and Basic2 Tab Setting

select the word alignment and other
ports based on your requirements and
complete the MegaWizard

Table 3–13. FC-4G Protocol Settings (Part 3 of 3)

Tab Page and Option

Setting

Содержание Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Stratix II GX

Отзывы:

Похожие инструкции для Stratix II GX

Бренды по названию

Популярные бренды

Altera Stratix II GX, Руководство пользователя

Результаты поиска

Содержание Stratix II GX

Отзывы:

Похожие инструкции для Stratix II GX

Бренды по названию

Популярные бренды