manualshive.com logo in svg

Alpha 6000S series, Руководство пользователя

Поделиться
Скачать
Alpha 6000S series Скачать руководство пользователя страница 157

Chapter 5 Detailed Function Introductions

156

0: No display

1: Display

Notes:

If PC.11 is set to 1, output voltage will be displayed in monitoring state, and the unit indicator “V” will be
lit up. If it is set to 0, output voltage will not be displayed.

If PC.12 is set to 1, bus voltage will be displayed in monitoring state, and the unit indicator “V” will be lit
up. If it is set to 0, bus voltage will not be displayed.

PC.13 AI1 (V)

Setting range: 0.1 [0]

PC.14 AI2 (V)

Setting range: 0.1 [0]

PC.15 AI3 (V) (Reserved for 3004GB and the
below)

Setting range: 0.1 [0]

0: No display

1: Display

Notes:

If PC.13 is set to 1, analog input voltage AI1 will be displayed in monitoring state, and the unit indicator “V”
will be lit up . If it is set to 0, analog input voltage AI1 will not be displayed.

If PC.14 is set to 1, analog input voltage AI2 will be displayed in monitoring state, and the unit indicator “V”
will be lit up. If it is set to 0, analog input voltage AI2 will not be displayed.

If PC.15 is set to 1, analog input voltage AI3 will be displayed in monitoring state, and the unit indicator “V”
will be lit up . If it is set to 0, analog input voltage AI1 will not be displayed.

PC.16 Analog PID feedback (no unit)

Setting range: 0.1 [0]

PC.17 Analog PID feed (no unit)

Setting range: 0.1 [0]

0: No display

1: Display

Notes:

Analog PID setting/feedback: the physical quantity percentage corresponding to the Analog

×

analog closed

loop range

When PC.16 is set as 1, the analog PID feedback will be displayed in the monitoring state without the
indication unit. If it is set as 0, the target will not be displayed.

When PC.17 is set as 1, the analog PID setting can be displayed in the monitoring state. When P7.00 is set as
0 and P7.08 is not as 0, the analog PID setting can be adjusted on lone by switching to PC.16 or PC.17 with
the shift key >> and will be saved in P7.06 after pressing ENTER. During the on-line adjustment, PC.17 will
be displayed. The target before adjustment will be displayed after adjustment is over.

PC.18 External counting value (no unit)

Setting range: 0.1 [0]

0: No display

1: Display

Notes:

If PC.18 is set to 1, external count value will be displayed in monitoring state, and all unit indicators will be
off. If it is set to 0, external count value will not be displayed.

PC.19 Terminal status (no unit)

Setting range: 0.1 [0]

0: No display

1: Display

Notes:

When PC.19 is set as 1, the terminal state will be displayed. If it is set as 0, the target will not be displayed.

The terminal state information includes the state of the multifunctional terminals X1~X11, two-way open
collector output terminals D0, Y1, Y2, Y3, output relay 1 and output relay 2. The state of the function
terminals is indicated by ON/OFF of the specified segment of an LED digital tube. If the digital tube segment
is on, it indicates that the state of the corresponding terminal is the effective state; if it is off, it indicates the
state is the ineffective state. There are four constantly-on stroke segments with the digital tube to facilitate
observation. It is showed as in Figure 5-12-1:

Содержание 6000S series






























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды