Network Installation
Xerox ColorQube™ 9201/9202/9203
System Administrator Guide
89
9.
In the
Port Information
area:
a.
Leave the
[TCP Port Number]
set to 9100 for Port 1. If two additional ports are available,
click
[Default All]
to see if they set to 9101 and 9102 respectively (emulating HP JetDirect EX
Plus 3).
b.
Leave the
[Bidirectional]
and
[Maximum Connections]
settings at their default values.
c.
Set the
[End of Job Timeout]
to the number of seconds to wait before processing a job
without an End Of Job indicator.
d.
Leave the
[PDL Switching]
Enabled box at its default value.
10. Click on the
[Apply]
button to accept the changes.
11. Click on the
[OK]
button when you see the message
“Properties have been successfully
modified”
.
Note:
The settings are not applied until you restart the device.
12. Click on the
[Status]
tab, select
[Description & Alerts]
in the directory tree.
13. Click the
[Reboot Machine]
button and click
[OK]
to reboot the device. The network controller
takes approximately 5 minutes to reboot and network connectivity will be unavailable during this
time.
14. A Configuration Report should have printed (by default) when the device rebooted. If the
Configuration Report did not print, go to the device:
a.
Press the
<Machine Status>
button.
b.
Touch the
[Machine Information]
tab.
c.
Touch
[Information Pages]
.
d.
Touch
[Configuration Report]
.
e.
Touch
[Print]
, then touch
[Close]
.
15. Review the settings for Raw TCP/IP Printing under the heading TCP/IP Settings. These settings
should read as follows:
a.
Raw TCP/IP Printing Enabled: Enabled.
b.
Raw TCP/IP Port Number: 9100.
Create an IPP Printer at your Workstation
Verify the correct software is loaded
1.
At your Workstation, right-click the
[My Network Places]
icon.
2.
Select
[Properties]
.
3.
Right-click on the
[Local Area Connection]
icon.
4.
Click
[Properties]
.
5.
Verify that the
[Internet Protocol (TCP/IP)]
protocol has been loaded.
Install the Print Driver
1.
From the
[Start]
menu, select
[Settings]
and then
[Printers]
(Windows 2000) or
[Printers and
Faxes]
(Windows XP). The Vista path is Start\Control Panel\Printer(s).
2.
Double-click the
[Add Printer]
icon and click
[Next]
.
3.
Verify that
[Network Printer]
is selected and click
[Next]
.
Summary of Contents for ColorQube 9201
