Network Installation
Xerox ColorQube™ 9201/9202/9203
System Administrator Guide
79
c.
Enter the device’s SMB (Server Message Block protocol) host name in the
[SMB Host Name]
field.
d.
Enter a descriptive host name comment in the
[SMB Host Name Comment]
field (if
required).
e.
Enter the device’s share name in the
[Share Name]
field.
f.
Enter a descriptive share name comment in the
[Share Name Comment]
field.
Physical Connection
displays the physical network connection, and will display
“Ethernet”
.
Transport
displays the current transport layer protocol, and will display
“TCP/IP”
.
g.
Enter the maximum number of simultaneous connections the server is allowed in the
[Maximum Connections]
field. The range is 10 - 30, and the default is 30.
h.
Enter the timeout value for outgoing connection attempts in the
[Connection Timeout]
field.
The range is 1 - 32767 seconds, and the default is 600 seconds.
9.
If you do not need to configure WINS, then click on the
[Apply]
button to accept the changes or
[Undo]
to return the settings to their previous values.
10. Click on the
[OK]
button when you see the message
“Properties have been successfully
modified”
.
Configure WINS (if used)
When running WINS the device registers its IP address and NetBIOS Hostname with a WINS server.
WINS allow the device to communicate using hostname only, removing a significant overhead from
the systems administrators.
WINS server address is stored in the file
/smart/etc/wins.
Name.
It is possible to manually enable WINS and configure primary and secondary WINS servers through
Internet Services.
1.
In the
Microsoft Networking
page, scroll down to the
WINS
section.
2.
In the
Server Information
area for
WINS
:
a.
For
Protocol
, check the
[Enabled]
checkbox to enable WINS.
b.
Enter the IP Address in the
[Primary Server IP Address]
of a Primary Server.
c.
Enter the IP Address in the
[Secondary Server IP Address]
of a Secondary Server.
Note:
If DHCP is configured, WINS IP Address(es) will be overridden.
Note:
WINS may be used for Address Resolution in addition to DNS. Microsoft Networking needs
to be enabled for the device to register services with WINS.
3.
Click on the
[Apply]
button to accept the changes or
[Undo]
to return the settings to their
previous values.
4.
Click on the
[OK]
button when you see the message
“Properties have been successfully
modified”
.
Note:
The settings are not applied until you reboot the device.
5.
Click on the
[Status]
tab, select
[Description & Alerts]
in the directory tree.
6.
Click the
[Reboot Machine]
button and click
[OK]
to reboot the machine. The network controller
takes approximately 5 minutes to reboot and network connectivity will be unavailable during this
time.
Summary of Contents for ColorQube 9201
