Network Installation
Xerox ColorQube™ 9201/9202/9203
System Administrator Guide
73
SLP is used to announce and look up services on a local network. When SLP is enabled, the device
becomes a Service Agent (SA) and announces its services to a User Agents (UA) via SLP.
1.
At your Workstation, open the web browser and enter the
IP address
of the device in the Address
bar, and press
[Enter]
.
2.
Click on the
[Properties]
tab.
3.
If prompted, enter the Administrator User ID and Password. The default is
[admin]
and
[1111]
.
4.
Click on the
[Login]
button.
5.
Click on the
[Connectivity]
link.
6.
Click on the
[Protocols]
link.
7.
Select
[SLP]
in the directory tree.
8.
In the
General
area:
a.
For
Protocol,
check the
[Enabled]
checkbox to enable Service Location Protocol (SLP).
b.
Enter an IP address for the
[Directory Agent]
, if required. This will specify the address of a
single Directory Agent (DA) to be added to the list of Directory Agents in the device’s DA list.
c.
Enter the required name(s) for
[Scope 1,2,3]
, this allows the System Administrator to set one
of the three manually configurable scope names. A scope is a searchable group or container
to which an agent may be associated. The default scope is called
“DEFAULT”
.
d.
For
Message Type
, select either
[Multicast]
or
[Broadcast]
from the drop-down menu. This
setting defines whether SLP will use multicast or broadcast in communications. Multicast
packets are routed between subnets as needed, but broadcast are not.
e.
Enter a value for
Multicast Radius
(0-255), the default is 255. This allows the System
Administrator to reconfigure the Multicast Radius for SLP. This is similar to the Time To Live
(TTL) in the TCP/IP parameter, and defines how many routers the multicast packet may cross.
f.
Enter a value for
MTU
to set the Maximum Transmission Unit (484 - 32768), with 1400 as
the default. This allows the System Administrator to set the maximum packet size for SLP.
g.
Version
will display the SLP version number supported by the device.
h.
Port Number
will display the socket (port) that all SLP communications will use. All devices
are required to listen on port 427 for UDP and TCP packets.
i.
Character Set
will display the character set in use. The default is US-ASCII.
9.
Click on the
[Apply]
button to accept the changes or
[Undo]
to return the settings to their
previous values.
10. Click on the
[OK]
button when you see the message
“Properties have been successfully
modified”
.
Note:
The settings are not applied until you restart the device.
11. Click on the
[Status]
tab, select
[Description & Alerts]
in the directory tree.
12. Scroll down and click the
[Reboot Machine]
button and click
[OK]
to reboot the device. The
network controller takes approximately 5 minutes to reboot and network connectivity will be
unavailable during this time.
SNMP
The System Administrator uses this page to enable or disable Simple Network Management Protocol
(SNMP).
Summary of Contents for ColorQube 9201
