manualshive.com logo in svg

Xerox ColorQube 9201, System Administrator Manual

Share
Download
Xerox ColorQube 9201 System Administrator Manual Download Page 55

General Setup

Xerox ColorQube™ 9201/9202/9203

System Administrator Guide

47

Online / Offline

The Online/Offline window allows the System Administrator to stop and resume the system from 
receiving or sending jobs over the network.

At the Device:

1.

Press the 

<Log In/Out>

 button to enter the Tools pathway.

2.

Enter the Administrator’s User Name 

[admin]

, touch 

[Next]

, enter Password 

[1111]

, touch 

[Enter]

.

3.

Press the 

<Machine Status>

 button.

4.

Touch the 

[Tools]

 tab.

5.

Touch 

[Network Settings]

.

6.

Touch

 [Online/Offline]

.

7.

To stop the device receiving or sending jobs over the network touch the 

[Offline] 

button. Any 

installed optional features using the network (for example Workflow Scanning) will not be 
available until the device is set to Online.

Note:

To enable the device to receive or send jobs over the network touch the 

[Online] 

button.

8.

Touch 

[Close]

.

9.

Press the 

<Log In/Out>

 button, then touch 

[Logout]

 to exit the Tools pathway.

Auxiliary (Foreign Device) Interface Kit

A third party access and accounting device, such as a coin operated device or a card reader can be 
attached to the device. To enable this option, the Foreign Device Interface Kit must be installed. After 
the kit is installed the administrator must enable Auxiliary Access as the Accounting Mode from the 
Tools menu of the device, as follows:

1.

Press the

 <Log In/Out>

 button.

2.

Enter the Administrator’s User Name 

[admin]

, touch 

[Next]

, enter Password 

[1111]

, touch 

[Enter]

.

3.

Press the 

<Machine Status>

 button. 

4.

Touch the 

[Tools]

 tab.

5.

Touch 

[Accounting Settings]

.

6.

Touch 

[Accounting Mode]

.

7.

Select 

[Auxiliary Access]

.

8.

Select the required

 [Auxiliary Device Configuration] 

and configure your device and touch 

[Save]

.

9.

Touch 

[Save]

.

10. Press the 

<Log In/Out>

 button, then touch 

[Logout]

 to exit the Tools pathway.

For further instructions on Auxiliary (Foreign Device) Interface Setup options refer to the 

Interactive 

User Guide

 delivered with your device.

Summary of Contents for ColorQube 9201

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands