background image

5A-34 Automatic Transmission/Transaxle: 

No Lock-Up Occurs

S3RH0B5104020

System Description

TCM turns TCC solenoid OFF under any of the following conditions.
• Engine coolant temperature is lower than 50 

°

C (122 

°

F).

• TCM detects the following DTCs.

P0715 / P0720 / P0743 / P0748 / P0753 / P0758 / P1700 / P1702

Troubleshooting

WARNING

!

 

• When performing a road test, select a place where there is no traffic or possibility of a traffic 

accident and be very careful during testing to avoid occurrence of an accident.

• Road test should be carried out with 2 persons, a driver and tester, on a level road.

 

Step

Action

Yes

No

1

Was “A/T System Check” performed?

Go to Step 2.

Go to “A/T System 
Check”.

2

Check DTC

Is DTC P0715, P0720, P0743, P0748, P0753, P0758, 
P1700 or P1702 detected?

Perform DTC Flow to 
repair and retry.

Go to Step 3.

3

1) Perform running test under the following conditions and 

check voltage between terminal “G08-12” of TCM 
connector and ground.
• Selector lever is in “D” range.
• Engine coolant temperature is normal operating 

temperature.

• Cruise control switch is turned OFF.
• Drive vehicle with TCC ON condition referring to 

“Automatic Gear Shift Diagram”.

Is terminal voltage about 10 – 14 V?

Faulty TCC solenoid 
valve, circuit or 
transaxle.

Substitute a known-
good TCM and recheck.

Summary of Contents for Liana RH418




















































































































































































































































































































































































Reviews: