2 Parameters
2.2 List of parameters
SINAMICS DCM
350
List Manual (LH8), 02/2015, 6RX1800-0ED76
Description:
Displays the value for the property set in p9206.
A value is only displayed for integer type properties.
Dependency:
Refer to: p9206, r9208
Description:
Displays the value for the property set in p9206.
A value is only displayed for string type properties.
Dependency:
Refer to: p9206, r9207
Note:
An ASCII table (excerpt) can be found, for example, in the appendix to the List Manual.
Description:
Sets the component number for a component to get its status LED to flash.
Dependency:
Refer to: p9211
Description:
Sets the function for the component selected in p9210.
After initiating a function, the parameter is automatically reset again.
Example:
- Set the component number (p9210).
- Select the "flashing on" function (set p9211 = 1).
Value:
-1:
Select function
0:
Flashing off
1:
Flashing on
Dependency:
Refer to: p9210
Notice:
If a task cannot be executed (e.g. the component number in p9210 does not exist), the following applies:
- There is no negative feedback signal.
- The value is reset anyway.
r9207
Topology direct access integer value / Topo access int
CU_DC, CU_DC_R,
CU_DC_R_S,
CU_DC_S
Can be changed:
-
Calculated:
-
Access level:
3
Data type:
Unsigned32
Dyn. index:
-
Func. diagram:
-
P-Group:
Topology
Unit group:
-
Unit selection:
-
Not for motor type:
-
Scaling:
-
Expert list:
1
Min Max
Factory
setting
- -
-
r9208[0...50]
Topology direct access string / Topo access string
CU_DC, CU_DC_R,
CU_DC_R_S,
CU_DC_S
Can be changed:
-
Calculated:
-
Access level:
3
Data type:
Unsigned8
Dyn. index:
-
Func. diagram:
-
P-Group:
Topology
Unit group:
-
Unit selection:
-
Not for motor type:
-
Scaling:
-
Expert list:
1
Min Max
Factory
setting
- -
-
p9210
Flashing component number / Flash comp_no
CU_DC, CU_DC_R,
CU_DC_R_S,
CU_DC_S
Can be changed:
U, T
Calculated:
-
Access level:
3
Data type:
Unsigned16
Dyn. index:
-
Func. diagram:
-
P-Group:
Topology
Unit group:
-
Unit selection:
-
Not for motor type:
-
Scaling:
-
Expert list:
1
Min Max
Factory
setting
0 499
0
p9211
Flash function / Flash fct.
CU_DC, CU_DC_R,
CU_DC_R_S,
CU_DC_S
Can be changed:
U, T
Calculated:
-
Access level:
3
Data type:
Integer16
Dyn. index:
-
Func. diagram:
-
P-Group:
Topology
Unit group:
-
Unit selection:
-
Not for motor type:
-
Scaling:
-
Expert list:
1
Min Max
Factory
setting
-1 1
-1
Summary of Contents for SINAMICS DCM
