Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 219

Page: 219 / 264

Installation

7.4 Connecting SITOP UPS1100 battery modules to the UPS module

SITOP UPS1600 / BAT1600 / UPS1100
Equipment Manual, 07.2021, A5E37775406-11-76

219

The connected battery module is automatically detected.

Note

When connecting several battery modules in parallel (max. 6) the following applies:
1.

Ensure that the battery modules are the same type and have the same charge state.

Battery modules are wired to the UPS in a star configuration with the same cable lengths

(ensure that the impedance is the same for all cables).

Dimension the cable cross-section from the neutral point to the UPS for the total current!

Proceed as follows, to connect several SITOP UPS1100 battery modules:
1.

Connect several battery modules in parallel to the power terminals and the communication

terminals of the SITOP UPS1600.

Figure 7-5

Wiring for up to 6 battery modules connected in parallel

Check that the wiring is correct.

Insert the fuses.

The connected battery modules are automatically identified after several seconds.

WARNING

Danger due to high short-circuit current

Before inserting the fuses, check the correct polarity of the wiring of all of the connected

battery modules.

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands