Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 216

Page: 216 / 264

Installation

7.3 Connecting SITOP BAT1600 battery modules to the UPS module

SITOP UPS1600 / BAT1600 / UPS1100

216

Equipment Manual, 07.2021, A5E37775406-11-76

By connecting up to 6 SITOP BAT1600 battery modules of the same type in parallel, battery

modules with a low rating can be connected to a SITOP UPS1600 with a higher power rating.

The following table lists the recommended combinations of SITOP UPS1600 and SITOP

BAT1600 battery modules.

Battery modules

SITOP UPS1600

10 A

SITOP UPS1600

20 A

SITOP UPS1600

40 A

SITOP BAT1600 2.5 Ah Li

-1

SITOP BAT1600 3.2 Ah Pb

-2

SITOP BAT1600 7.5 Ah Li

SITOP BAT1600 12 Ah Pb

SITOP BAT1600 38 Ah Pb

X is a recommended combination

O is a combination that is not recommended

-1

By connecting two identical battery modules in parallel, this type can also be used with a

SITOP UPS1600 20 A system.

-2

By connecting two identical battery module types in parallel, this type can also be used with

a SITOP UPS1600 40 A system.

Connecting battery modules from third-party manufacturers to the SITOP UPS1600

Batteries from other manufacturers can be used. However, note that without a data interface

there is no full BMS functionality. Automatic temperature compensation of the end-of-

charging voltage is not possible. When manually configuring the energy storage, carefully

observe the data provided by the battery manufacturer and continually monitor the charging

parameters! It is only permissible to connect battery modules using "Pb technology" or "pPb

technology"!

Note
Connecting third-party battery modules

When connecting third-party battery modules, data connection via the COM connections is

not possible.

Note

If third-party battery modules are to be used, then all of the modules connected to a UPS

module must be of the same type. The connected modules must have the same technological

parameters and the same service life.

Note

When using third-party battery modules, the approval according to IEC62368-1 and UL61010

is no longer valid.

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands