Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 176

Page: 176 / 264

Engineering and remote access

3.10 OPC UA server

SITOP UPS1600 / BAT1600 / UPS1100

176

Equipment Manual, 07.2021, A5E37775406-11-76

ActualState

Display name

Data type

Definition

Description

BatteryCalculated

Health

Byte

AnalogItemType Calculated battery state (only for SITOP BAT1600)

BatteryOperatingState Byte

AnalogItemType Battery status (only for SITOP BAT1600)

ModuleCapacity

Float

AnalogItemType Battery capacity: Total battery capacity of all energy storage

devices connected to the SITOP UPS1600.

ModuleChange

Recommended

Boolean

PropertyType

Battery capacity is insufficient to achieve the specified buffer

time.

ModuleCompound

Enumeration

MultiState

DiscreteType

Connected device

ModuleConnection

Fault

Boolean

PropertyType

Connection to battery interrupted - check connection and

fuse

ModuleManufactoring

Date

PropertyType

Manufacturing date

ModuleMax

Temperature

Sbyte

AnalogItemType Maximum specified operating temperature of the battery.

ModuleMin

Temperature

Sbyte

AnalogItemType Minimum specified operating temperature of the battery.

ModuleStandbyTime

UInt32

AnalogItemType Battery-specific data: Time for which battery was connected

but no power was consumed.

ModuleStateLed

Object

Sitop_1600_

LedType

ModuleStateLed

ModuleTemperature

Sbyte

AnalogItemType Battery temperature

Alarm

Display name

Data type

Definition

Description

AlarmBatteryChange

Canceled

Boolean

PropertyType

Battery replacement canceled - battery parameters are not

reset.

AlarmBatteryChange

Finished

Boolean

PropertyType

Battery replacement finished - counters have been reset.

AlarmBatteryChange

Started

Boolean

PropertyType

Battery replacement started by user

AlarmBattery

CommunicationFault

Boolean

PropertyType

Communication with formerly known battery is no longer

possible - check communication

AlarmBatteryDeepDis-

chargedNoCharging

Possible

Boolean

PropertyType

Battery is deep discharged, charging not possible.

AlarmBatteryDefect

Boolean

PropertyType

Battery defective - check fuse and battery voltages.

AlarmBatteryEndOf

LifetimePrewarning

Boolean

PropertyType

Calculated battery service life almost reached. Only restrict-

ed buffer readiness probable.

AlarmBattery

EndOfLifetimeWarning

Boolean

PropertyType

Calculated battery service life reached, battery replacement

recommended.

AlarmBattery

TemperatureHigh

Boolean

PropertyType

Battery temperature too high - battery life will be shortened

AlarmBattery

TemperatureLow

Boolean

PropertyType

Battery temperature too low - reduced output current

AlarmFuseBroken

Boolean

PropertyType

Fuse is defective.

AlarmIncompatible

ModuleDetected

Boolean

PropertyType

Incompatible battery module detected.

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands