Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 114

Page: 114 / 264

Engineering and remote access

3.6 Cyclic and acyclic data

SITOP UPS1600 / BAT1600 / UPS1100

114

Equipment Manual, 07.2021, A5E37775406-11-76

0x0006: Device information parameters (reading)

Data

Description

Data type

HW revision

Hardware version

Unsigned16

SW revision

Software release

Unsigned16

Boot loader version

Unsigned16

Max output current [1 A]

Maximum output current

Unsigned8

Fill byte(s)

1 x Unsigned8

MLFB/Order number

MLFB/order number (Article number)

VisibleString(20)

Serial number

VisibleString(16)

Device name

VisibleString(30)

Version number

VisibleString(50)

0x0007: Hardware settings parameters (reading)

Data

Description

Data type

Buffer time [1 s]

Buffer time: After the selected buffer time has expired, the SITOP

UPS1600 switches off the load output. The actual buffer time that

can be achieved depends on the connected loads and energy stor-

age devices.

Unsigned16

Buffer threshold [0.01 V]

Connection threshold: Switching voltage for buffering. Buffering is

active below this value.

Unsigned16

Buffering allowed

Activate or deactivate buffer mode. This setting is only accepted by

the SITOP UPS1600 in the Remote Enable (REN) operating mode.

Unsigned8

Enable reset

Enable reset: If, during buffer mode, the input voltage becomes

available again, then the output of the SITOP UPS1600 is switched

off for a selectable time in order to reset connected loads.

Unsigned8

Start from battery

Start from battery: Setting at the signal terminal for function "Start

from battery".

Unsigned8

Selected battery profile

Profile of the selected battery: The battery charging behavior is set

at the signal terminals. The setting is only used, if the SITOP

UPS1600 is not in the "Remote Enable" (REN) mode.

Unsigned8

0x0008: Buffering parameters (reading/writing)

Data

Description

Data type

Expected buffer current [0.1 Ah]

from V2.0 and higher

Expected buffer current: Estimated average load current during

buffer mode.

Unsigned16

0x0009: Maintenance parameters (reading/writing)

Data

Description

Data type

Resistor test interval [1 h] from

V2.1

R test interval

Unsigned16

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands