Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 215

Page: 215 / 264

Installation

7.3 Connecting SITOP BAT1600 battery modules to the UPS module

SITOP UPS1600 / BAT1600 / UPS1100
Equipment Manual, 07.2021, A5E37775406-11-76

215

Connecting several SITOP BAT1600 battery modules

To extend the power failure buffering time, up to 6 identical SITOP BAT1600 battery modules

can be connected to a SITOP UPS1600.
The connected battery module is automatically detected.

Note

When connecting several battery modules in parallel (max. 6) the following applies:
1.

Ensure that the battery modules are the same type and have the same charge state.

Battery modules are wired to the UPS in a star configuration with the same cable lengths

(ensure that the impedance is the same for all cables).

Dimension the cross-section of the star configuration wiring for the total current (if required,

reduce all fuse values).

Proceed as follows, to connect several SITOP BAT1600 battery modules:
1.

Connect several battery modules in parallel to the power terminals and the communication

terminals of the UPS module corresponding to the following wiring schematic.

Figure 7-4

Recommended wiring for up to 6 battery modules connected in parallel

Check that the wiring is correct.

Insert the fuses.

The connected battery modules are automatically identified after several seconds.

WARNING

Danger due to high short-circuit current

Before inserting the fuses, check the correct polarity of the wiring of all of the connected

battery modules.

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands