Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 68

Page: 68 / 264

Engineering and remote access

3.4 SIMATIC STEP 7 in the TIA Portal

SITOP UPS1600 / BAT1600 / UPS1100

Equipment Manual, 07.2021, A5E37775406-11-76

3.4.6

Assigning SITOP BAT1600 / UPS1100 battery modules to the basic unit SITOP

UPS1600

The basic functions of the uninterruptible power supply are available with all of the battery

modules that are compatible with the SITOP UPS1600. The SITOP UPS1100 5 Ah LiFePO4

battery is only supported by SITOP UPS1600 from software version V2.1; all SITOP BAT1600

battery modules first from software version V2.4.

Additional functions are available with battery module SITOP BAT1600 or SITOP UPS1100:
•

Automatic detection of the battery module rated values

•

Automatic management of up to six battery modules

•

Temperature-controlled charging

•

Charge status display

•

Battery status (battery health) status display for SITOP BAT1600

•

Diagnostics using the SITOP Manager and the web server

Using an example, in the following steps you are shown how the SITOP UPS1600 is assigned

a battery module.

Note

Only SITOP BAT1600 or SITOP UPS1100 battery modules of the same type can be added to

the slots of a SITOP UPS1600.
The number of battery modules that can be configured is limited to six. The description is

only applicable to devices that were linked to via the HSP.

Preconditions

•

STEP 7 in the TIA Portal has been opened and a project has been created.

•

A SITOP UPS1600 has been integrated in the project.

Procedure

The procedure is only applicable for devices integrated using HSP.
1.

In the device view, select the SITOP UPS1600 basic unit.

In the Hardware catalog , navigate to the SITOP BAT1600/UPS1100 battery modules under

"Power supply and distribution\Power supplies\SITOP UPS\UPS1100".

Select the required battery module in the hardware catalog.

In the "Information" area you can see information about the expansion module, and when

necessary you can change the preselected (default) version.

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands