Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 92

Page: 92 / 264

Engineering and remote access

3.5 SIMATIC STEP 7

SITOP UPS1600 / BAT1600 / UPS1100

Equipment Manual, 07.2021, A5E37775406-11-76

3.5.4

Parameter assignment

3.5.4.1

Parameters of the basic device and battery module

The adjustable parameters of the basic unit SITOP UPS1600 and the SITOP BAT1600 battery

modules or SITOP UPS1100 are structured according to subgroups in SIMATIC STEP 7. These

subgroups are shown in the table below.

Subgroup

Description

Buffer parameters

Parameters to configure the response of the SITOP UPS1600 when buffering

Reset parameters

Configuring the interruption when the supply voltage returns

Buffering parameters (2) Parameters for determining the possible buffer time
Maintenance

Battery test interval

Third-party battery

Parameters for using third-party batteries

Charging

Parameters for the charging behavior:
•

End-of-charge voltage

•

Charge current

Web server

Web server settings

OPC UA

OPC UA server settings

NTP settings

Time synchronization via the Network-Time-Protocol

PROFINET security

PROFINET safety settings

A detailed description of the individual parameters of the subgroups is contained in the

associated section under Parameterizing SITOP UPS1600 (Page 92).

3.5.4.2

Parameterizing SITOP UPS1600

The procedure is the same for all parameters. This section describes the general procedure to

reach the configuration dialog. The individual parameters and their possible values are

described in the following subsections.
Each parameter has a start value. A click on "Reset to initial values" resets all parameters of a

subgroup to the associated start value.

Preconditions

•

The SITOP UPS1600 has been integrated in the opened project and networked.

Procedure

Open the Network view "NetPro" ("Options > Configure network").

The controller and the networked SITOP UPS1600 are displayed.

In the Network view click on SITOP UPS1600. The hardware configuration opens.

Double click in the hardware configuration on the SITOP UPS1600 entry in the station

window for slot 0.1.

In the configuration dialog click on the "Parameters" tab.

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands