Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 173

Page: 173 / 264

Engineering and remote access

3.10 OPC UA server

SITOP UPS1600 / BAT1600 / UPS1100
Equipment Manual, 07.2021, A5E37775406-11-76

173

Display name

Data type

Definition

Description

RemainingLockTime

Duration

PropertyType

Remaining time to the inhibit

RenewLock

Method

Renew lock in order to prevent the lock from expiring

Method is not supported.

3.10.6.15

MethodSet

Display name

Data type

Definition

Description

AddUser

Method

Adds a user.

ChangeUserPassword Method

Method

Changes a user password.

ClearAlarmHistory

Method

Deletes the alarm history.

DeleteUser

Method

Removes a user.

DownloadDevice

Configuration

Method

Downloads the device configuration.

RegenerateCertificate Method

Method

Initiate the generation of a new safety certificate.

RemoteReset

Method

Executes a remote reset.

RemoteReset2

Method

Executes a remote reset.

ResetSystem

Method

Resets the system to the initial state.

ResetToFactory

Settings

Method

Reset to factory settings.

SendRSignal

Method

Initiate that a reset signal is sent

SendSSignal

Method

Initiate that a shutdown signal is sent

SetNetworkParameter Method

Method

Sets the network parameters.

ShowAlarmHistory

Method

Shows the alarm history.

ShowPending

AlarmList

Method

Shows the list of active alarms.

UpdateFirmware

Method

Updates the firmware.

UploadAlarmHistory

Method

Uploads the alarm history.

UploadCertificate

Method

Uploads a certificate.

UploadDevice

Configuration

Method

Uploads the device configuration.

UploadLicence

Information

Method

Uploads license information.

UploadPendingAlarm

List

Method

Uploads the list of active alarms.

3.10.6.16

Network

Display name

Data type

Definition

Description

NetworkDHCPEnable

Boolean

PropertyType

Activation of DHCP

NetworkGateway

String[16]

PropertyType

Router address

NetworkIP

String[16]

PropertyType

IP address

NetworkSubnetmask

String[16]

PropertyType

Subnet mask

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands