manualshive.com logo in svg

Siemens 6EP4131-0GB00-0AY0, Equipment Manual, Page: 220 / 264

Share
Download
Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 220

Installation 

 

7.4 Connecting SITOP UPS1100 battery modules to the UPS module 

 

SITOP UPS1600 / BAT1600 / UPS1100  

220

 

Equipment Manual, 07.2021, A5E37775406-11-76 

By connecting up to 6 SITOP UPS1100 battery modules of the same type in parallel, battery 

modules with a low rating can be connected to a SITOP UPS1600 with a higher power rating. 

The following table lists the recommended combinations of SITOP UPS1600 and SITOP 

UPS1100 battery modules. 

 

Battery modules 

SITOP UPS1600 

10 A 

SITOP UPS1600 

20 A 

SITOP UPS1600 

40 A 

SITOP UPS1100 1.2 Ah Pb 

X 

-1

 

O 

SITOP UPS1100 2.5 Ah Pb 

X 

X 

-2

 

SITOP UPS1100 3.2 Ah Pb 

X 

X 

-2

 

SITOP UPS1100 5 Ah Li 

X 

X 

-2

 

SITOP UPS1100 7 Ah Pb 

X 

X 

X 

SITOP UPS1100 12 Ah Pb 

X 

X 

X 

X is a recommended combination 

O is a combination that is not recommended 

-1

 By connecting two identical battery modules in parallel, this type can also be used with a 

SITOP UPS1600 20 A system. 

-2 

 By connecting two identical battery module types in parallel, this type can also be used 

with a SITOP UPS1600 40 A system. 

Connecting battery modules from third-party manufacturers to the SITOP UPS1600 

Batteries from other manufacturers can be used. However, note that without a data interface 

there is no full BMS functionality. Automatic temperature compensation of the end-of-

charging voltage is not possible. When manually configuring the energy storage, carefully 

observe the data provided by the battery manufacturer and continually monitor the charging 

parameters! It is only permissible to connect battery modules using "Pb technology" or "pPb 

technology"! 
Third-party battery modules can be parameterized with UPS devices with interface. The 

parameterization is taken from the saved configuration for the two REMOTE and MANUAL 

operating modes. The parameters are applicable for all battery modules in a chain. 

 

 

Note 
Connecting third-party battery modules 

When connecting third-party battery modules, data connection via the COM connections is 

not possible. 

 

 

Note 

If third-party battery modules are to be used, then all of the modules connected to a SITOP 

UPS1600 must be of the same type. The connected modules must have the same 

technological parameters and the same service life. 

 

 

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Reviews:

No comments