Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 84

Page: 84 / 264

Engineering and remote access

3.4 SIMATIC STEP 7 in the TIA Portal

SITOP UPS1600 / BAT1600 / UPS1100

Equipment Manual, 07.2021, A5E37775406-11-76

3.4.10

Firmware update

WARNING

The SITOP UPS1600 is reset while updating the firmware. For safety reasons, the

output is switched off.

Ensure that no damage is caused to the plant or system.
Ensure that the PG/PC and/or all switches, routers and gateways that are used have an

independent power supply during the firmware update.

WARNING

Firmware update to V2.3.0 with UPS Manager

If the UPS Manager was used to update the firmware to V2.3.0 for devices with PROFINET

interface, then the update cannot be successfully completed. In a case such as this, the

device signals a software error using LED 1 (O.K./BAT.). Such a device can be made

operational again by performing an update using the web server, see Firmware update with

web server (Page 135).

Note

Install the current version of the SITOP Managers, before you start the firmware update. The

installation file for the SITOP Manager is available at no charge on the SITOP home page

(

http://www.siemens.com/sitop

) or directly

(

https://support.industry.siemens.com/cs/ww/en/view/109760607

Note

Do not switch-off the devices during the firmware update.

The files for updating the firmware (firmware updates) are available online under

(

http://support.automation.siemens.com/WW/view/en/79207181

). Different firmware

updates are offered depending on the amp rating of the SITOP UPS1600.

Note
Observe the compatibility of the firmware!

Other firmware updates are not compatible.
Determine the amp rating of your SITOP UPS1600 and download the appropriate firmware

update.

Note

From device firmware 2.3, a downgrade can be made to version 2.2.3. A downgrade is not

supported for older versions. Information on how to read out the firmware release from the

device is provided in Section Diagnostics (Page 82).

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands