Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 88

Page: 88 / 264

Engineering and remote access

3.5 SIMATIC STEP 7

SITOP UPS1600 / BAT1600 / UPS1100

Equipment Manual, 07.2021, A5E37775406-11-76

3.5

SIMATIC STEP 7

3.5.1

Introduction

The uninterruptible power supply SITOP UPS1600 can be used with SIMATIC STEP 7 from

Version 5 and higher.
In SIMATIC STEP 7 the basic unit SITOP UPS1600 and its battery modules SITOP BAT1600 or

UPS1100 can be integrated in projects, parameterized and diagnosed.

Note

SIMATIC STEP 7 and the SITOP Manager cannot simultaneously access the SITOP UPS1600. It

is not permissible that the SITOP Manager service runs while the system is being accessed via

SIMATIC STEP 7.

3.5.2

Installing the generic station description file (GSD)

To use the SITOP UPS1600 and the SITOP BAT1600 or SITOP UPS1100 battery modules in

SIMATIC STEP 7, you must install the corresponding generic station description file (GSD). The

GSD file is available at our SITOP-homepage (

http://www.siemens.com/sitop-ups1600

) or

directly at (

https://support.industry.siemens.com/cs/ww/en/view/75854605

Preconditions

•

SIMATIC STEP 7 has been opened and a project has been created.

•

At least one station has been added.

•

You know where the GSD data have been saved.

Procedure

Download the GSD file from the Internet.

Close all stations in HW Config.

Open menu "Options > Install GSD files...".

Click on "Browse ...", and select the folder in which the GSD-file is located.

Select the GSD file and click on "Install".

Note

If the file was not able to be installed, or if errors occurred during installation, then

SIMATIC STEP 7 V5.6 creates a log file. Click on "Display log" to open the log file.

This GSD file can be used in SIMATIC STEP 7 V5.5 without any restrictions.

In the "Options" menu, click on "Update Catalog".

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands